Applicable to equipment using copper cables, copper bars or aluminium bars as the earthing and shortcircuiting media.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 1<\/td>\n | BRITISH STANDARD <\/td>\n<\/tr>\n | ||||||
| 2<\/td>\n | Committees responsible for this British Standard <\/td>\n<\/tr>\n | ||||||
| 3<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | Foreword Foreword to amendment A11 <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | 1 Scope 2 Normative references <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | 3 Definitions 3.1 Tests 3.1.1 type test 3.1.2 routine test 3.1.3 sampling test 3.1.4 acceptance test 3.2 Special terms 3.2.1 portable equipment for earthing or earthing and short-circuiting 3.2.2 earthing cable 3.2.3 short-circuiting device 3.2.4 short-circuiting cable 3.2.5 short-circuiting bar 3.2.6 connecting cluster <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 3.2.7 earth clamp 3.2.8 line clamp 3.2.9 fixed connection point 3.2.10 insulating element 3.2.11 earthing pole (earthing stick) 3.2.12 conductive extension component 3.2.13 rated current 3.2.14 peak current 4 Data for electrical characteristics <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 5 Requirements 5.1 General requirements Table 1 – Special temperature categories 5.2 Cables for earthing and short-circuiting <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | Table 2 – Minimum cross-section of earthing cable related to the cross-section of the short-circuiting cabl… 5.3 Short-circuiting bars 5.4 Connections within devices 5.5 Clamps 5.6 Complete earthing and short-circuiting device <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 5.7 Insulating elements 5.8 Marking 5.9 Manufacturer\u2019s instructions for use <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 6 Tests 6.1 General <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 6.2 Fatigue test on cable with end-fittings <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | Table 3 – List of tests referred to subclauses and test categories <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 6.3 Humidity penetration test on devices with copper cables 6.4 Pull test on cable with clamps Table 4 – Pull test force on cable and connections 6.5 Test on clamps, fixed connection points and connections within devices with respect to abilit… <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 6.6 Short-circuit current test <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | Table 5 – Maximum tightening torques to be applied for screw-tightened clamps at the \ufffd\ufffd\ufffd\ufffd\ufffdshort-circuit cur… <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | Table 6 – Peak current factor <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | 6.7 Testing durability of marking <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | Figure 1 – Illustrations of assembled portable equipment for earthing or earthing and\ufffdshort-circuiting <\/td>\n<\/tr>\n | ||||||
| 22<\/td>\n | Figure 2 – Illustrations of three-pole earthing and short-circuiting cable devices <\/td>\n<\/tr>\n | ||||||
| 23<\/td>\n | Figure 3 – Illustration of a three-pole earthing and short-circuiting device with short-circuiting bar and e… <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | Figure 4 – Test set-ups for testing multi-pole short-circuiting devices for connection to rigid\ufffdconductors <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | Figure 5 – Test set-ups for testing multi-pole short-circuiting devices for overhead lines <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | Figure 6 – Test set-ups for testing single-pole devices for overhead lines in single-phase systems and earth… <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | Figure 7 – Apparatus for fatigue-testing with bending and twisting <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | Annex A (normative) Instructions for selection, use and maintenance of earthing or earthing and short-cir… A.1 General A.2 Selection A.3 Usage <\/td>\n<\/tr>\n | ||||||
| 29<\/td>\n | A.4 Maintenance and disposal Annex B (normative) Sampling procedure Table B.1 – Single sampling plan for normal inspection <\/td>\n<\/tr>\n | ||||||
| 30<\/td>\n | Annex C (normative) Interim rules for selection and testing of earthing poles C.1 Selection Table C.1 – Basic data for earthing poles C.2 Bending test C.3 Torsion test C.4 Marking <\/td>\n<\/tr>\n | ||||||
| 31<\/td>\n | Figure C.1 – Arrangement for bending tests on earthing poles Annex D (normative) Additional requirements and tests for devices using cables connected in parallel D.1 Requirements <\/td>\n<\/tr>\n | ||||||
| 32<\/td>\n | D.2 Tests Figure D.1 – Test set-ups for the testing of multi-pole short-circuiting devices with paralleled cables connec… <\/td>\n<\/tr>\n | ||||||
| 33<\/td>\n | Figure D.2 – Test set-ups for the testing of multi-pole short-circuiting devices with paralleled\ufffdcables connec… <\/td>\n<\/tr>\n | ||||||
| 34<\/td>\n | Figure D.3 – Test set-ups for the testing of the following earthing and short-circuiting devices\ufffdusing cables … <\/td>\n<\/tr>\n | ||||||
| 35<\/td>\n | Annex ZA (informative) Acceptance tests Annex ZB (normative) Normative references to international publications with their corresponding European … <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Live working. Portable equipment for earthing or earthing and short-circuiting<\/b><\/p>\n |