{"id":26567,"date":"2024-10-17T02:33:20","date_gmt":"2024-10-17T02:33:20","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/astm-a635-2009-3\/"},"modified":"2024-10-24T13:47:41","modified_gmt":"2024-10-24T13:47:41","slug":"astm-a635-2009-3","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/astm\/astm-a635-2009-3\/","title":{"rendered":"ASTM-A635 2009"},"content":{"rendered":"<\/p>\n

1.1 This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils.<\/p>\n

1.2 It applies to Specification A 1018\/A 1018M .<\/p>\n

1.3 This material is available only in coils described as follows:<\/p>\n

A<\/span><\/sup> Hot-rolled heavy thickness sheet in coils less than 12 in. [300 mm] and less in width must have slit edges. Hot-rolled heavy thickness coils 12 in. [300 mm] and wider with mill edge is considered hot-rolled heavy thickness strip.<\/p>\n

Note<\/span> 1The changes in width limits with the publication of A 635\/A 635M 06a result in a change in tensile testing direction for material from 0.180 in. [4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in. [1200 mm] wide as that material is now covered by Specification A 568\/A 568M 06a. The purchaser is advised to discuss this change with the supplier.<\/p>\n

1.4 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.<\/p>\n

1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 2) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the M specification is used.<\/p>\n

Note<\/span> 2The term weight<\/span> is used when inch-pound units are the standard. However, under SI, the preferred term is mass<\/span> .<\/p>\n

1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.<\/p>\n

1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable M specification designation (SI units), the material shall be furnished to inch-pound units.<\/p>\n

PDF Catalog<\/h4>\n\n\n\n\n\n\n\n\n\n\n\n\n
PDF Pages<\/th>\nPDF Title<\/th>\n<\/tr>\n
1<\/td>\nScope
Referenced Documents <\/td>\n<\/tr>\n
2<\/td>\nTerminology
Index of Tables, Dimensions, and Allowances
Materials and Manufacture
Chemical Composition <\/td>\n<\/tr>\n
3<\/td>\nMechanical Properties
Dimensions and Tolerances
Workmanship, Finish, and Appearance
TABLE 1 <\/td>\n<\/tr>\n
4<\/td>\nRetests and Disposition of Non-Conforming Material
TABLE 2
TABLE 3
TABLE 4
TABLE 5
TABLE 6 <\/td>\n<\/tr>\n
5<\/td>\nInspection
Rejection and Rehearing
Test Reports and Certification
TABLE 7
TABLE 8
TABLE 9 <\/td>\n<\/tr>\n
6<\/td>\nProduct Marking
Packaging and Package Marking
Keywords
TABLE S1.1 <\/td>\n<\/tr>\n
7<\/td>\nTABLE S1.2
TABLE S1.3 <\/td>\n<\/tr>\n
8<\/td>\nA1. PERMISSIBLE VARIATIONS IN DIMENSIONS AND MASS IN SI UNITS
A1.1
TABLE S1.4
TABLE A1.1 <\/td>\n<\/tr>\n
9<\/td>\nTABLE A1.2
TABLE A1.3
TABLE A1.4
TABLE A1.5 <\/td>\n<\/tr>\n
10<\/td>\nTABLE A1.6
TABLE A1.7
TABLE A1.8 <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"

A635\/A635M-09a Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
ASTM<\/b><\/a><\/td>\n2009<\/td>\n11<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":26568,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[1118,2637],"product_tag":[],"class_list":{"0":"post-26567","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-77-140-50","7":"product_cat-astm","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/26567","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/26568"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=26567"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=26567"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=26567"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}