ASTM-D2265 2000
$40.63
D2265-00 Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range
| Published By | Publication Date | Number of Pages |
| ASTM | 2000 | 5 |
1.1 This test method covers the determination of the dropping point of lubricating grease.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | Scope Referenced Documents Terminology Summary of Test Method |
| 2 | Significance and Use Apparatus Sampling FIG. 1 |
| 3 | Preparation of Apparatus Procedure FIG. 2 |
| 4 | Calculation Report Precision and Bias FIG. 3 |
| 5 | Keywords X1. PRECISION VALUES X1.1 X1.2 |
Related products
-
ASTM-D6265 2009
D6265-09 Standard Practice for Separation of Contaminants in Polymers Using an Extruder Filter Test Published…
-
ASTM-D2265 2020
D2265-20 Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range Published…
-
ASTM-D2225 2020(Redline)
D2225-20 Standard Test Methods for Silicone Liquids Used for Electrical Insulation (Redline) Published By Publication…
-
ASTM-D2665 2000
D2665-00 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings…
-
ASTM-D2275 2008(Redline)
D2275-01(2008)e1 Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial…
-
ASTM-D2268 2003
D2268-93(2003)e1 Standard Test Method for Analysis of High-Purity n-Heptane and Isooctane by Capillary Gas Chromatography…
-
ASTM-D2065 2003
D2065-03 Standard Test Method for Determination of Edge Performance of Composite Wood Products Under Surfactant…
-
ASTM-E2265 2007
E2265-07 Standard Terminology for Anchors and Fasteners in Concrete and Masonry Published By Publication Date…
-
ASTM-D2865 2001
D2865-01 Standard Practice for Calibration of Standards and Equipment for Electrical Insulating Materials Testing Published…
-
ASTM-D2265 2020(Redline)
D2265-20 Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range (Redline)…
-
ASTM-E2265 2003
E2265-03 Standard Terminology for Anchors and Fasteners in Concrete and Masonry Published By Publication Date…
-
ASTM-D2260 2003
D2260-03 Standard Tables of Conversion Factors and Equivalent Yarn Numbers Measured in Various Numbering Systems…
-
ASTM-D6265 2009(Redline)
D6265-09 Standard Practice for Separation of Contaminants in Polymers Using an Extruder Filter Test (Redline)…
-
ASTM-D2665 2008
D2665-08 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings…
-
ASTM-D2565 2008
D2565-99(2008) Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications Published By Publication…
-
ASTM-D2256 2008
D2256-02(2008) Standard Test Method for Tensile Properties of Yarns by the Single-Strand Method Published By…
-
ASTM-D2256 2009
D2256/D2256M-09 Standard Test Method for Tensile Properties of Yarns by the Single-Strand Method Published By…
-
ASTM-D2260 2009
D2260-03(2009) Standard Tables of Conversion Factors and Equivalent Yarn Numbers Measured in Various Numbering Systems…
-
ASTM-D2225 2004
D2225-04 Standard Test Methods for Silicone Fluids Used for Electrical Insulation Published By Publication Date…
-
ASTM-E2265 2009
E2265-09 Standard Terminology for Anchors and Fasteners in Concrete and Masonry Published By Publication Date…
-
ASTM-D4265 2007
D4265-98(2007)e1 Standard Guide for Evaluating Stain Removal Performance in Home Laundering Published By Publication Date…
-
ASTM-D2265 2006(Redline)
D2265-06 Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range (Redline)…
-
ASTM-E2265 2004
E2265-04a Standard Terminology for Anchors and Fasteners in Concrete and Masonry Published By Publication Date…
-
ASTM-D3265 2005
D3265-05 Standard Test Method for Carbon Black—Tint Strength Published By Publication Date Number of Pages…
-
ASTM-E2265 2004
E2265-04 Standard Terminology for Anchors and Fasteners in Concrete and Masonry Published By Publication Date…
-
ASTM-D2665 2004
D2665-04ae1 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings…
-
ASTM-E2265 2006
E2265-06a Standard Terminology for Anchors and Fasteners in Concrete and Masonry Published By Publication Date…
-
ASTM-E2265 2009(Redline)
E2265-09 Standard Terminology for Anchors and Fasteners in Concrete and Masonry (Redline) Published By Publication…
-
ASTM-D2266 2001
D2266-01 Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method) Published By…
-
ASTM-D2256 2010
D2256/D2256M-10e1 Standard Test Method for Tensile Properties of Yarns by the Single-Strand Method Published By…
-
ASTM-D3265 2001
D3265-01 Standard Test Method for Carbon Black—Tint Strength Published By Publication Date Number of Pages…
-
ASTM-D2205 2010
D2205-85(2010) Standard Guide for Selection of Tests for Traffic Paints Published By Publication Date Number…
-
ASTM-D2665 2007
D2665-07 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings…
-
ASTM-D2225 2020
D2225-20 Standard Test Methods for Silicone Liquids Used for Electrical Insulation Published By Publication Date…
-
ASTM-D2665 2020(Redline)
D2665-20 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings…
-
ASTM-D2255 2002
D2255-02e1 Standard Test Method for Grading Spun Yarns for Appearance Published By Publication Date Number…
-
ASTM-D2235 2004
D2235-04 Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings Published By…
-
ASTM-D2665 2010
D2665-10 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings…
-
ASTM-D3265 2000
D3265-00 Standard Test Method for Carbon Black—Tint Strength Published By Publication Date Number of Pages…
-
ASTM-D2265 2006
D2265-06 Standard Test Method for Dropping Point of Lubricating Grease Over Wide Temperature Range Published…
