AWWA C110 2008

$75.83

AWWA C110-08: Ductile-Iron And Gray-Iron Fittings

Published By	Publication Date	Number of Pages
AWWA	2008	78

Guaranteed Safe Checkout

Category: AWWA

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

This standard covers 3- to 48-in. (76- to 1,219-mm) gray-iron and/or ductile-iron fittings to be used with ductile-iron pipe for water.

PDF Catalog

PDF Pages	PDF Title
1	ANSI/AWWA C110/A21.10-08
3	Committee Personnel
7	Contents
9	Foreword I. Introduction.
15	II. Special Issues. III. Use of This Standard.
17	IV. Major Revisions. V. Comments.
19	AWWA Standard Ductile-Iron and Gray-Iron Fittings SECTION 1: GENERAL Sec. 1.1 Scope
20	Sec. 1.2 Purpose Sec. 1.3 Application SECTION 2: REFERENCES
21	SECTION 3: DEFINITIONS
22	SECTION 4: REQUIREMENTS Sec. 4.1 Materials Sec. 4.2 Permeation Sec. 4.3 General Requirements
23	Sec. 4.4 Coatings and Linings
24	Sec. 4.5 Special Requirements for Flanged Fittings SECTION 5: VERIFICATION Sec. 5.1 Inspection and Certification by Manufacturer
25	Sec. 5.2 Inspection by Purchaser Sec. 5.3 Tolerances or Permitted Variations
26	Sec. 5.4 Acceptance Tests Table 1 Gray-iron test specimens and acceptance values
27	Sec. 5.5 Chemical Limitations
28	Sec. 5.6 Additional Tests Required by the Purchaser Sec. 5.7 Defective Specimens and Retests Sec. 5.8 Rejection of Fittings Sec. 5.9 Determining Rejection SECTION 6: DELIVERY Sec. 6.1 Marking
29	Table 2 Minimum dimensional requirements for cast markings Sec. 6.2 Notice of Nonconformance Sec. 6.3 Affidavit of Compliance
30	Table 3 Plain-end dimensions and tolerances for mechanical-joint fittings
32	Table 4 Mechanical-joint bends
33	Table 4 Mechanical-joint bends (continued)
34	Table 4 Mechanical-joint bends (continued)
35	Table 4 Mechanical-joint bends (continued)
36	Table 5 Mechanical-joint tees and crosses
37	Table 5 Mechanical-joint tees and crosses (continued)
38	Table 5 Mechanical-joint tees and crosses (continued)
39	Table 5 Mechanical-joint tees and crosses (continued)
40	Table 5 Mechanical-joint tees and crosses (continued)
41	Table 5 Mechanical-joint tees and crosses (continued)
42	Table 5 Mechanical-joint tees and crosses (continued)
43	Table 6 Mechanical-joint base bends
44	Table 7 Mechanical-joint base tees
45	Table 8 Mechanical-joint reducers
46	Table 8 Mechanical-joint reducers (continued)
47	Table 8 Mechanical-joint reducers (continued)
48	Table 8 Mechanical-joint reducers (continued)
49	Table 9 Mechanical-joint tapped tees*
50	Table 10 Mechanical-joint offsets
51	Table 11 Mechanical-joint sleeves
52	Table 12 Mechanical-joint caps and plugs
53	Table 13 Mechanical-joint connecting pieces
54	Table 14 Connecting pieces, one-end flanged
55	Table 15 Flange details
56	Table 16 Base drilling details
57	Table 17 Flanged bends
58	Table 18 Flanged tees and crosses
59	Table 18 Flanged tees and crosses (continued)
60	Table 18 Flanged tees and crosses (continued)
61	Table 18 Flanged tees and crosses (continued)
62	Table 18 Flanged tees and crosses (continued)
63	Table 18 Flanged tees and crosses (continued)
64	Table 19 Flanged base bends
65	Table 20 Flanged base tees
66	Table 21 Flanged reducers
67	Table 21 Flanged reducers (continued)
68	Table 21 Flanged reducers (continued)
69	APPENDIX A Flanged Fittings-Bolts, Gaskets, and Installation SECTION A.1: BOLTS AND NUTS SECTION A.2: GASKETS
70	SECTION A.3: INSTALLATION
71	Table A.1 Flange gasket details
73	APPENDIX B Special Fittings
76	Wall Pipe