AWWA C111 2007

$75.83

AWWA C111-07: Rubber Gasket Joints For Ductile-Iron Pressure Pipe And Fittings

Published By	Publication Date	Number of Pages
AWWA	2007	52

Guaranteed Safe Checkout

Category: AWWA

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

This standard covers rubber-gasket joints of the following types for ductile-iron pressure pipe and ductile-iron and gray-iron fittings, valves, hydrants, and other appurtenances for water supply service: mechanical joint; push-on joint; flanged joint; and modifications to push-on and mechanical joints. The purpose of this standard is to provide purchasers, manufacturers, and constructors with the minimum requirements for rubber-gasket joints for ductile-iron pressure pipe and fittings, including materials, design, inspection, testing, marking, and shipping.

PDF Catalog

PDF Pages	PDF Title
1	ANSI/AWWA C111/A21.11-07
3	Committee Personnel
7	Contents
9	Foreword I. Introduction.
13	II. Special Issues.
15	III. Use of This Standard. IV. Major Revisions
16	V. Comments.
17	AWWA Standard Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings SECTION 1: GENERAL Sec. 1.1 Scope
18	Sec. 1.2 Purpose Sec. 1.3 Application SECTION 2: REFERENCES
19	SECTION 3: DEFINITIONS
20	SECTION 4: REQUIREMENTS Sec. 4.1 Materials Sec. 4.2 Permeation
21	Sec. 4.3 General Requirements Sec. 4.4 Special Requirements for the Mechanical Joint
22	Table 1 Properties for gray-iron glands
24	Table 2 Mechanical-joint dimensions—in.
25	Table 2 Mechanical-joint dimensions—in. (continued)
26	Table 3 Mechanical-joint gasket dimensions, 3 in.–48 in.
27	Table 4 Required properties and methods of testing for SBR mechanical-joint gaskets
28	Table 5 Standard design for low-alloy steel tee-head bolt and nut dimensions—in.
29	Table 6 Minimum characteristic values for steel tee-head bolts
30	Table 7 Minimum proof test for tee-head bolts and nuts Sec. 4.5 Special Requirements for the Push-on Joint
31	Table 8 Required properties and methods of testing for SBR push-on joint gaskets
32	Table 9 Flange details Sec. 4.6 Special Requirements for the Flanged Joint
34	Table 10 Minimum working pressure ratings for mechanical and push-on joints Sec. 4.7 Performance Requirements
36	SECTION 5: VERIFICATION Sec. 5.1 Inspection Sec. 5.2 Certification and Test Records SECTION 6: DELIVERY Sec. 6.1 Marking
37	Sec. 6.2 Packing Sec. 6.3 Affidavit of Compliance
39	APPENDIX A Mechanical-Joint Bolts, Gaskets, and Installation SECTION A.1: TEE-HEAD BOLTS AND NUTS SECTION A.2: GASKETS SECTION A.3: INSTALLATION
41	Table A.1 Mechanical-joint bolt torque loads
43	APPENDIX B Push-on Joint Design, Gaskets, Lubricant, and Installation SECTION B.1: JOINT DESIGN
44	SECTION B.2: GASKETS SECTION B.3: LUBRICANT SECTION B.4: INSTALLATION
45	Table B.1 Push-on joint assembly
47	APPENDIX C Flanged-Joint Bolts, Gaskets, and Installation SECTION C.1: BOLTS AND NUTS SECTION C.2: GASKETS
48	Table C.1 Flange gasket details
49	SECTION C.3: INSTALLATION
52	ADOPTION NOTICE