BS EN 4617:2006
$102.76
Aerospace series. Recommended practices for standardizing company standards
| Published By | Publication Date | Number of Pages |
| BSI | 2006 | 16 |
This document is a guide describing the recommended practices in specifying industrial requirements in the form of recognised standards (national, European, international), in preference to company standards. It emphasises the economic and industrial value of following and encouraging such practices. It is based on what is frequently observed and considered by primes and manufacturers as constituting best practices to the benefit of all involved in the life cycle of a product, from the design stage until its withdrawal from service…..
Related products
-
BS EN 14617-10:2005
Agglomerated stone. Test methods – Determination of chemical resistance Published By Publication Date Number of…
-
BS EN 4613:2009
Aerospace series. Spherical plain bearings in corrosion resisting steel with self-lubricating liner, narrow series. Dimensions…
-
BS EN 14617-2:2016
Agglomerated stone. Test methods – Determination of flexural strength (bending) Published By Publication Date Number…
-
BS EN ISO 4671:2001
Rubber and plastics hoses and hose assemblies. Methods of measurement of dimensions Published By Publication…
-
BS EN 14617-16:2005
Agglomerated stone. Test methods – Determination of dimensions, geometric characteristics and surface quality of modular…
-
BS EN 14617-2:2004:2005 Edition
Agglomerated stone. Test methods – Determination of flexural strength (bending) Published By Publication Date Number…
-
BS EN ISO 4611:2001
Plastics. Determination of the effects of exposure to damp heat, water spray and salt mist…
-
BS EN ISO 4017:2001
Hexagon head screws. Product grades A and B Published By Publication Date Number of Pages…
-
BS EN 14617-11:2005
Agglomerated stone. Test methods – Determination of linear thermal expansion coefficient Published By Publication Date…
-
BS EN 14617-2:2008
Agglomerated stone. Test methods – Determination of flexural strength (bending) Published By Publication Date Number…
-
BS EN 4697:2016
Aerospace series. General and installation requirements for passenger seat fittings Published By Publication Date Number…
-
BS EN 4017:2001
Aerospace series. Pipe coupling 8°30′ in titanium alloy. Elbows 90° Published By Publication Date Number…
-
BS EN 4167:2003
Aerospace series. Clips, spring tension, three parts. Inner clips in heat resisting steel FE-PA92HT (A286)…
-
BS EN 2617:2001
Aerospace Series. Plates in titanium and titanium alloys. Thickness 6 mm < a ≤ 100…
-
BS EN ISO 4614:2000:1999 Edition
Plastics. Melamine-formaldehyde mouldings. Determination of extractable formaldehyde Published By Publication Date Number of Pages BSI…
-
BS EN 4697:2016
Aerospace series. General and installation requirements for passenger seat fittings Published By Publication Date Number…
-
BS EN ISO 4611:2008
Plastics. Determination of the effects of exposure to damp heat, water spray and salt mist…
-
BS EN 14617-8:2007
Agglomerated stone. Test methods – Determination of resistance to fixing (dowel hole) Published By Publication…
-
BS EN 4627:2007 2008
Aerospace series. Steel FE-PM 3504 (X4CrNiMo16-5-1). Air melted. Hardened and tempered. Forgings. De ≤ 150…
-
BS EN 14617-6:2005
Agglomerated stone. Test methods – Determination of thermal shock resistance Published By Publication Date Number…
-
BS EN 417:2003:2009 Edition
Non-refillable metallic gas cartridges for liquefied petroleum gases, with or without a valve, for use…
-
BS EN 4614:2009
Aerospace series. Spherical plain bearings in corrosion resisting steel with self-lubricating liner, wide series. Dimensions…
-
BS EN 4618:2009
Aerospace series. Aircraft internal air quality standards, criteria and determination methods Published By Publication Date…
-
BS EN 4117:2004
Aerospace series. Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-PH2601 (Inconel 718), silver…
-
BS EN 14617-9:2005
Agglomerated stone. Test methods – Determination of impact resistance Published By Publication Date Number of…
-
BS EN 4616:2005
Aerospace series. Magnesium alloy MG-C18002. T4. Chill casting Published By Publication Date Number of Pages…
-
BS EN 14617-13:2005:2006 Edition
Agglomerated stone. Test methods – Determination of electrical resistivity Published By Publication Date Number of…
-
BS EN 14617-15:2005
Agglomerated stone. Test methods – Determination of compressive strength Published By Publication Date Number of…
-
BS EN 4317:2007:2008 Edition
Aerospace series. Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15). Non heat treated, forging stock a or D…
-
BS EN 14617-5:2005
Agglomerated stone. Test methods – Determination of freeze and thaw resistance Published By Publication Date…
-
BS EN 14617-4:2005
Agglomerated stone. Test methods – Determination of abrasion resistance Published By Publication Date Number of…
-
BS EN ISO 4618:2006
Paints and varnishes. Terms and definitions Published By Publication Date Number of Pages BSI 2006…
-
BS EN 4610:2005:2006 Edition
Aerospace series. Pipe coupling with 8° 30′ in titanium alloy. Elbows 45°, with thrust wire…
-
BS EN 4117:2003
Aerospace series. Nuts, bihexagonal, self-locking, in heat resisting nickel base alloy NI-PH 2601 (Inconel 718),…
-
BS EN ISO 4610:2001:2002 Edition
Plastics. Vinyl chloride homopolymer and copolymer resins. Sieve analysis using air-jet sieve apparatus Published By…
-
BS EN 4167:2004:2005 Edition
Aerospace series. Clips, spring tension, three parts. Inner clips in heat resisting steel FE-PA2601 (A286)…
-
BS EN 4615:2005
Aerospace series. Magnesium alloy MG-C18002. T4. Sand casting Published By Publication Date Number of Pages…
-
BS EN ISO 4167:2006
Polyolefin agricultural twines Published By Publication Date Number of Pages BSI 2006 20
-
BS EN 14617-12:2005
Agglomerated stone. Test methods – Determination of dimensional stability Published By Publication Date Number of…
-
BS EN ISO 4617:2000
Paints and varnishes. List of equivalent terms Published By Publication Date Number of Pages BSI…
