RI FuelGasCode 2019 1stptg
$51.73
Rhode Island Fuel Gas Code, 1st Printing
| Published By | Publication Date | Number of Pages |
| RI | 2019 | 227 |
This is a fully integrated code based on the 2015 IFGC.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | 2019 RHODE ISLAND FUEL GAS CODE |
| 2 | 2019 RHODE ISLAND FUEL GAS CODE BASED ON THE 2015 INTERNATIONAL FUEL GAS CODE® TITLE PAGE |
| 3 | COPYRIGHT |
| 4 | PREFACE |
| 8 | EFFECTIVE USE OF THE INTERNATIONAL FUEL GAS CODE |
| 10 | LEGISLATION |
| 12 | RHODE ISLAND STATE BUILDING CODE SBC-19 STATE FUEL GAS CODE |
| 13 | REGULATION SBC-19 STATE FUEL GAS CODE AUGUST 1, 2019 |
| 14 | STATE OF RHODE ISLAND BUILDING CODE STANDARDS COMMITTEE |
| 15 | STATE BUILDING CODE REGULATIONS – 2019 |
| 16 | TABLE OF CONTENTS |
| 18 | CHAPTER 23–27.3 STATE BUILDING CODE § 23-27.3-100.0 SCOPE § 23-27.3-100.1 SHORT TITLE – APPLICABILITY § 23-27.3-100.1.1 CHAPTER TITLE – APPLICABILITY § 23-27.3-100.1.2 PURPOSE § 23-27.3-100.1.3 CREATION OF THE STATE BUILDING CODE STANDARDS COMMITTEE |
| 19 | § 23-27.3-100.1.4 APPOINTMENT AND QUALIFICATIONS OF THE COMMITTEE § 23-27.3-100.1.5 BUILDING CODE – ADOPTION AND PROMULGATION BY COMMITTEE |
| 20 | § 23-27.3-100.1.5.1 HOUSING AND MAINTENANCE CODE § 23-27.3-100.1.5.2 EXISTING CODES § 23-27.3-100.1.5.3 STATE REHABILITATION BUILDING AND FIRE CODE FOR EXISTING BUILDINGS AND STRUCTURES § 23-27.3-100.1.5.4 STATE ENERGY CONSERVATION CODE |
| 21 | § 23-27.3-100.1.5.5 HURRICANE, STORM, AND FLOOD STANDARDS § 23-27.3-100.1.6 COMMITTEE AS BOARD OF STANDARDS AND APPEALS – POWERS AND DUTIES – APPEALS § 23-27.3-100.1.7 EFFECT OF LOCAL CODES – REPEAL OF LOCAL AUTHORITY § 23-27.3-100.1.8 SEVERABILITY § 23-27.3-100.2 APPLICATION OF REFERENCES § 23-27.3-100.3 CONSTRUCTION § 23-27.3-100.4 SPECIALIZED CODES INCORPORATED |
| 22 | § 23-27.3-101.0 MATTERS COVERED § 23-27.3-101.1 EXEMPTION FOR ORDINARY REPAIRS § 23-27.3-101.2 MATTERS NOT COVERED § 23-27.3-101.2.1 PROPOSED BUILDINGS § 23-27.3-101.2.2 BUILDINGS AND STRUCTURES, EXISTING AND UNDER CONSTRUCTION § 23-27.3-101.3 ZONING RESTRICTIONS § 23-27.3-102.0 ORDINARY REPAIRS § 23-27.3-103.0 INSTALLATION OF SERVICE EQUIPMENT § 23-27.3-104.0 MAINTENANCE |
| 23 | § 23-27.3-104.1 OWNER RESPONSIBILITY § 23-27.3-105.0 CHANGE IN EXISTING USE 23-27.3-105.1 CONTINUATION OF EXISTING USE § 23-27.3-105.2 CHANGE IN USE AND OCCUPANCY § 23-27.3-105.3 PART CHANGE IN USE § 23-27.3-105.4 REESTABLISHMENT OF A PRIOR USE § 23-27.3-106.0 EXISTING STRUCTURES § 23-27.3-106.1 SUBSTANTIAL IMPROVEMENTS § 23-27.3-106.2 SUBSTANTIAL DAMAGES EXCEEDING FIFTY PERCENT |
| 24 | § 23-27.3-106.3 IMPROVEMENTS AND DAMAGES BETWEEN TWENTY-FIVE AND FIFTY PERCENT OF VALUE § 23-27.3-106.4 IMPROVEMENTS OR DAMAGES UNDER TWENTY-FIVE PERCENT OF VALUE § 23-27.3-106.5 PHYSICAL VALUE § 23-27.3-107.0 DEPARTMENT OF BUILDING INSPECTION § 23-27.3-107.1 LOCAL BUILDING OFFICIAL – APPOINTMENT § 23-27.3-107.1.1 LOCAL INSPECTOR § 23-27.3-107.2 ALTERNATE LOCAL BUILDING OFFICIAL |
| 25 | § 23-27.3-107.3 APPOINTMENT OF PERSONNEL BY STATE BUILDING COMMISSIONER § 23-27.3-107.4 QUALIFICATIONS AND DUTIES OF THE STATE BUILDING COMMISSIONER § 23-27.3-107.5 LOCAL BUILDING OFFICIAL – QUALIFICATIONS – POWERS AND DUTIES § 23-27.3-107.6 CERTIFICATION OF LOCAL BUILDING OFFICIALS – EDUCATIONAL PROGRAMS |
| 26 | § 23-27.3-107.7 RECERTIFICATION AND CONTINUING EDUCATION § 23-27.3-107.8 RESTRICTION ON EMPLOYEES’ ACTIVITIES § 23-27.3-107.9 RELIEF FROM PERSONAL RESPONSIBILITY § 23-27.3-108.0 DUTIES AND POWERS OF THE BUILDING OFFICIAL AND THE STATE BUILDING COMMISSIONER § 23-27.3-108.1 LOCAL BUILDING OFFICIAL – ENFORCEMENT DUTIES § 23-27.3-108.1.1 APPLICATIONS AND PERMITS § 23-27.3-108.1.3 NEW MATERIALS AND METHODS OF CONSTRUCTION |
| 27 | § 23-27.3-108.1.3.1 TEST RESULTS § 23-27.3-108.1.3.2 RETESTING § 23-27.3-108.1.4 INSPECTIONS § 23-27.3-108.1.5 REPLEALED § 23-27.3-108.1.6 ADMINISTRATIVE PROCEDURES § 23-27.3-108.1.7 DEPARTMENT RECORDS § 23-27.3-108.1.8 REPORTS § 23-27.3-108.2 STATE BUILDING COMMISSIONER’S DUTIES |
| 28 | § 23-27.3-108.2.0.1 REPEALED § 23-27.3-108.2.1 DUTIES OF COMMITTEE 23-27.3-108.2.2 COMPENSATION OF COMMITTEE MEMBERS § 23-27.3-108.2.3 EMERGENCY PROCEDURES § 23-27.3-108.2.4 MUNICIPAL ADVISORY COUNCIL ON STATEWIDE PERMITTING § 23-27.3-109.0 COMMITTEE § 23-27.3-109.1 COMMITTEE’S RULE MAKING AUTHORITY – LEGISLATIVE REPORT – LEGISLATIVE COMMITTEE |
| 29 | § 23-27.3-109.1.1 COMMITTEE – LICENSING OF LABORATORIES AND TEST PERSONNEL § 23-27.3-109.1.2 COMMITTEE – REGULATION OF MANUFACTURED BUILDINGS § 23-27.3-109.1.3 ADOPTION OF FEDERAL STANDARDS FOR MANUFACTURED HOMES § 23-27.3-109.1.3.1 INSPECTION OF MANUFACTURED HOMES MANUFACTURERS § 23-27.3-109.1.3.2 PENALTIES FOR VIOLATION AS TO MANUFACTURED HOMES |
| 30 | § 23-27.3-109.1.3.3 MONITORING INSPECTION FEE § 23-27.3-109.1.3.4 REPORTS OF MANUFACTURED HOME MANUFACTURERS, DISTRIBUTORS, AND DEALERS § 23-27.3-109.1.3.5 TEMPORARY GREENHOUSE DEFINED § 23-27.3-109.1.4 REPEALED § 23-27.3-109.2 ACCEPTED ENGINEERING PRACTICE § 23-27.3-109.3 PROPOSING AMENDMENTS TO RULES AND REGULATIONS § 23-27.3-110.0 MODIFICATIONS AND VARIANCES § 23-27.3-111.0 NEW AND ALTERED BUILDING AND STRUCTURE – INSPECTIONS § 23-27.3-111.1 PRELIMINARY INSPECTION § 23-27.3-111.2 INSPECTION |
| 31 | § 23-27.3-111.3 MANUFACTURING BUILDINGS 23-27.3-111.3.1 PLANT INSPECTION § 23-27.3-111.3.2 INSTALLATION SITE INSPECTION § 23-27.3-111.4 EXISTING BUILDINGS § 23-27.3-111.4.1 PERIODIC INSPECTIONS § 23-27.3-111.4.2 REPLEALED § 23-27.3-111.5 FINAL INSPECTION 23-27.3-111.6 INSPECTION SERVICES § 23-27.3-111.7 COORDINATION OF INSPECTIONS § 23-27.3-112.0 RIGHT OF ENTRY § 23-27.3-112.1 OFFICIAL IDENTIFICATION CARD |
| 32 | § 23-27.3-112.2 MUNICIPAL COOPERATION § 23-27.3-113.0 APPLICATION FOR PERMIT § 23-27.3-113.1 WHEN PERMIT IS REQUIRED § 23-27.3-113.1.1 ISSUANCE OF PERMITS FOR SIDING § 23-27.3-113.2 FORM OF APPLICATION § 23-27.3-113.3 BY WHOM APPLICATION IS MADE § 23-27.3-113.3.1 APPLICATIONS FOR WORK REQUIRING LICENSED WORKERS § 23-27.3-113.3.2 APPLICATIONS FOR WORK REQUIRING REGISTERED WORKERS |
| 33 | § 23-27.3-113.4 DESCRIPTION OF WORK § 23-27.3-113.5 PLANS AND SPECIFICATIONS § 23-27.3-113.5.1 REPLEALED § 23-27.3-113.6 PLOT PLAN § 23-27.3-113.6.1 APPROVAL OF AN INDIVIDUAL SEWAGE DISPOSAL SYSTEM § 23-27.3-113.7 ENGINEERING DETAILS § 23-27.3-113.8 AMENDMENTS TO APPLICATION § 23-27.3-113.9 TIME LIMITATION ON APPLICATION § 23-27.3-114.0 PERMITS § 23-27.3-114.1 ACTION ON APPLICATION |
| 34 | § 23-27.3-114.1.1 REPORTS TO ASSESSORS § 23-27.3-114.2 EXPIRATION OF PERMIT § 23-27.3-114.3 PREVIOUS APPROVALS |
| 35 | § 23-27.3-114.3.1 DRAWINGS AND SPECIFICATIONS § 23-27.3-114.4 BUILDING OFFICIAL TO SIGN PERMIT § 23-27.3-114.5 APPROVED PLANS § 23-27.3-114.6 REVOCATION OF PERMITS § 23-27.3-114.7 APPROVAL IN PART § 23-27.3-114.8 POSTING OF PERMIT § 23-27.3-114.9 NOTICE OF BUILDING START § 23-27.3-115.0 CONDITIONS OF PERMIT § 23-27.3-115.1 COMPLIANCE WITH CODE § 23-27.3-115.2 COMPLIANCE WITH PERMIT § 23-27.3-115.3 COMPLIANCE WITH PLOT PLAN § 23-27.3-115.4 CHANGE IN PLOT PLAN |
| 36 | § 23-27.3-115.5 DISMISSAL OF CONTRACTOR OR SUBCONTRACTOR § 23-27.3-116.0 MOVING, RAISING, SHORING, OR DEMOLITION OF BUILDINGS § 23-27.3-116.1 SERVICE CONNECTIONS § 23-27.3-116.2 BUILDINGS TO BE RODENT-ERADICATED PRIOR TO DEMOLITION § 23-27.3-116.3 DESCRIPTION AND INSPECTION OF BUILDINGS – TRAVEL ROUTE § 23-27.3-116.4 AGREEMENT CONDITION TO MOVING § 23-27.3-116.5 PUBLIC UTILITIES, WIRES, POLES, TREES, AND SHRUBS § 23-27.3-116.6 MOVING TO BE CONTINUOUS § 23-27.3-116.7 WATCHPERSON AND LIGHTS DURING MOVING |
| 37 | § 23-27.3-116.8 BONDS AND LIABILITY INSURANCE § 23-27.3-116.9 SHORING § 23-27.3-117.0 REMOVAL OF STRUCTURES § 23-27.3-117.1 LOT REGULATION § 23-27.3-118.0 FEES § 23-27.3-118.1 SPECIAL FEES § 23-27.3-118.2 RAMPS FOR DISABLED PERSONS § 23-27.3-119.0 FEE COMPUTATION § 23-27.3-120.0 CERTIFICATE OF USE AND OCCUPANCY § 23-27.3-120.1 NEW BUILDINGS § 23-27.3-120.2 BUILDINGS HEREAFTER ALTERED |
| 38 | § 23-27.3-120.3 EXISTING BUILDINGS § 23-27.3-120.4 CHANGES IN USE AND OCCUPANCY § 23-27.3-120.5 TEMPORARY OCCUPANCY § 23-27.3-120.6 CONTENTS OF CERTIFICATE § 23-27.3-121.0 POSTING BUILDINGS § 23-27.3-121.1 POSTED USE AND OCCUPANCY |
| 39 | § 23-27.3-121.2 POSTED OCCUPANCY LOAD § 23-27.3-121.3 FURNISHING OF POSTED SIGNS § 23-27.3-121.4 PERIODIC INSPECTION FOR POSTING § 23-27.3-122.0 VIOLATIONS § 23-27.3-122.1 NOTICE OF VIOLATION § 23-27.3-122.1.2 NOTICE OR ORDERS – SERVICE AND CONTENT 23-27.3-122.2 PROSECUTION OF VIOLATION § 23-27.3-122.3 PENALTIES § 23-27.3-122.4 ABATEMENT OF VIOLATIONS |
| 40 | § 23-27.3-123.0 STOP-WORK ORDER § 23-27.3-123.1 NOTICE TO OWNER § 23-27.3-123.1.1 POSTING OF ORDER § 23-27.3-123.2 UNLAWFUL CONTINUANCE § 23-27.3-124.0 UNSAFE STRUCTURES – GENERAL PROVISIONS § 23-27.3-124.1 UNSAFE CONDITIONS § 23-27.3-124.2 NOTICE OF UNSAFE CONDITION |
| 41 | § 23-27.3-124.3 APPEALS § 23-27.3-124.4 RESTORATION OF UNSAFE BUILDINGS § 23-27.3-124.4.1 COMPLIANCE § 23-27.3-124.5 DISREGARD OF UNSAFE NOTICE § 23-27.3-124.6 BOARDING |
| 42 | § 23-27.3-124.6.1 DISCONNECTION OF UTILITIES § 23-27.3-124.6.2 REMOVAL OF DEBRIS AND RUBBISH § 23-27.3-125.0 ENERGENCY MEASURES § 23-27.3-125.1 VACATING BUILDINGS § 23-27.3-125.2 TEMPORARY SAFEGUARDS § 23-27.3-125.3 CLOSING STREETS § 23-27.3-125.4 EMERGENCY REPAIRS § 23-27.3-125.5 HAZARDOUS BUILDINGS § 23-27.3-125.6 COSTS OF EMERGENCY REPAIRS § 23-27.3-125.7 LIEN FOR EMERGENCY REPAIRS § 23-27.3-126.0 APPEALS FROM ORDERS IN REGARD TO UNSAFE BUILDINGS |
| 43 | § 23-27.3-126.1 APPLICATION FOR REVIEW § 23-27.3-126.2 PROCEDURE § 23-27.3-126.3 FINDINGS § 23-27.3-127.0 STATE AND LOCAL BOARDS OF APPEALS § 23-27.3-127.1 COMMITTEE TO SERVE AS A BOARD OF STANDARDS AND APPEALS |
| 44 | § 23-27.3-127.1.1 STAY OF PROCEEDINGS § 23-27.3-127.1.2 GRANTING VARIANCE § 23-27.3-127.1.3 ADDITIONAL POWERS § 23-27.3-127.1.4 PROCEDURES – RECORD OF VARIANCES |
| 45 | § 23-27.3-127.2 LOCAL BOARD OF APPEALS § 23-27.3-127.2.1 MEMBERSHIP AND LOCAL BOARD § 23-27.3-127.2.2 STAY OF PROCEEDINGS § 23-27.3-127.2.3 GRANTING VARIANCE § 23-27.3-127.2.4 ADDITIONAL POWERS § 23-27.3-127.2.5 PROCEDURES |
| 46 | § 23-27.3-127.2.6 LOCAL DECISION TRANSMITTED TO STATE BOARD § 23-27.3-128.0 DESIGN AND CONSTRUCTION PROCEDURES § 23-27.3-128.1 SCOPE § 23-27.3-128.1.1 OWNER’S RESPONSIBILITIES § 23-27.3-128.1.2 – 23-27.3-128.1.5 REPEALED § 23-27.3-128.2 REPEALED § 23-27.3-128.2.1 DRAWINGS AND SPECIFICATIONS § 23-27.3-128.2.2 RESPONSIBILITIES |
| 47 | § 23-27.3-128.2.3 REPORTING § 23-27.3-128.3 CONSTRUCTION CONTRACTOR RESPONSIBILITIES § 23-27.3-128.4 TESTING REQUIRED § 23-27.3-128.5 BUILDING OFFICIAL’S RESPONSIBILITIES § 23-27.3-128.5.1 WAIVER OF PLAN EXAMINATION § 23-27.3-128.5.2 WAIVER OF DETAILED FIELD INSPECTION |
| 48 | § 23-27.3-128.5.3 INSPECTION WAIVER – UTILIZATION § 23-27.3-128.5.4 BUILDING PERMIT ISSUANCE OR REQUIREMENTS § 23-27.3-128.6 SPECIAL TECHNICAL SERVICES § 23-27.3-128.7 FEES AND COSTS § 23-27.3-129.0, 23-27.3-129.1 REPEALED § 23-27.3-129.2 REPEALED § 23-27.3-129.3 REPEALED § 23-27.3-200.0 SAVINGS CLAUSE § 23-27.3-300.0 PUBLICATION OF CODE § 23-27.3-400.0 SEVERABILITY |
| 49 | § 23-27.3-401.0 SALE OF PRESSURE VESSEL § 23-27.3-500.0 EFFECTIVE DATE OF CODE § 23-27.3-501.0, 23-27.3-502.0 REPEALED § 23-27.3-503.0, 23-27.3-504.0 [OBSOLETE] § 23-27.3-505.0 REPEALED § 23-27.3-506.0 [OBSOLETE] § 23-27.3-600.0 FRESH WATER WETLANDS § 23-27.3-700.0 REPEALED § 23-27.3-701.0 BABY CHANGING TABLES |
| 50 | CHAPTER 1 ADMINISTRATION PART 1—SCOPE AND APPLICATION SECTION 101 (IFGC) GENERAL |
| 51 | SECTION 102 (IFGC) APPLICABILITY |
| 52 | PART 2—ADMINISTRATION AND ENFORCEMENT SECTION 103 (IFGC) DEPARTMENT OF INSPECTION SECTION 104 (IFGC) DUTIES AND POWERS OF THE CODE OFFICIAL SECTION 105 (IFGC) APPROVAL SECTION 106 (IFGC) PERMITS SECTION 107 (IFGC) INSPECTIONS AND TESTING |
| 53 | SECTION 108 (IFGC) VIOLATIONS SECTION 109 (IFGC) MEANS OF APPEAL |
| 54 | SECTION 110 (IFGC) TEMPORARY EQUIPMENT, SYSTEMS AND USES |
| 56 | CHAPTER 2 DEFINITIONS SECTION 201 (IFGC) GENERAL SECTION 202 (IFGC) GENERAL DEFINITIONS |
| 66 | CHAPTER 3 GENERAL REGULATIONS SECTION 301 (IFGC) GENERAL |
| 67 | SECTION 302 (IFGC) STRUCTURAL SAFETY SECTION 303 (IFGC) APPLIANCE LOCATION |
| 68 | SECTION 304 (IFGS) COMBUSTION, VENTILATION AND DILUTION AIR EQUATION 3-1 EQUATION 3-2 |
| 69 | FIGURE 304.5.3 ALL AIR FROM INSIDE THE BUILDING (see Section 304.5.3) FIGURE 304.6.1(1) ALL AIR FROM OUTDOORS—INLET AIR FROM VENTILATED CRAWL SPACE AND OUTLET AIR TO VENTILATED ATTIC (see Section 304.6.1) |
| 70 | FIGURE 304.6.1(2) ALL AIR FROM OUTDOORS THROUGH VENTILATED ATTIC (see Section 304.6.1) FIGURE 304.6.1(3) ALL AIR FROM OUTDOORS (see Section 304.6.1) FIGURE 304.6.2 SINGLE COMBUSTION AIR OPENING, ALL AIR FROM THE OUTDOORS (see Section 304.6.2) |
| 71 | SECTION 305 (IFGC) INSTALLATION |
| 72 | SECTION 306 (IFGC) ACCESS AND SERVICE SPACE |
| 74 | SECTION 307 (IFGC) CONDENSATE DISPOSAL SECTION 308 (IFGS) CLEARANCE REDUCTION |
| 75 | TABLE 308.2 a through k REDUCTION OF CLEARANCES WITH SPECIFIED FORMS OF PROTECTION |
| 76 | FIGURE 308.2(1) EXTENT OF PROTECTION NECESSARY TO REDUCE CLEARANCES FROM APPLIANCE OR VENT CONNECTIONS FIGURE 308.2(2) WALL PROTECTOR CLEARANCE REDUCTION SYSTEM FIGURE 308.2(3) MASONRY CLEARANCE REDUCTION SYSTEM |
| 77 | SECTION 309 (IFGC) ELECTRICAL SECTION 310 (IFGS) ELECTRICAL BONDING SECTION 311 TEMPERATURE CONTROL |
| 78 | CHAPTER 4 GAS PIPING INSTALLATIONS SECTION 401 (IFGC) GENERAL SECTION 402 (IFGS) PIPE SIZING |
| 79 | EQUATION 4-1 EQUATION 4-2 TABLE 402.4 Cr AND Y VALUES FOR NATURAL GAS AND UNDILUTED PROPANE AT STANDARD CONDITIONS |
| 80 | TABLE 402.4(1) SCHEDULE 40 METALLIC PIPE |
| 81 | TABLE 402.4(2) SCHEDULE 40 METALLIC PIPE |
| 82 | TABLE 402.4(3) SCHEDULE 40 METALLIC PIPE |
| 83 | TABLE 402.4(4) SCHEDULE 40 METALLIC PIPE |
| 84 | TABLE 402.4(5) SCHEDULE 40 METALLIC PIPE |
| 85 | TABLE 402.4(6) SCHEDULE 40 METALLIC PIPE |
| 86 | TABLE 402.4(7) SCHEDULE 40 METALLIC PIPE |
| 87 | TABLE 402.4(8) SEMIRIGID COPPER TUBING |
| 88 | TABLE 402.4(9) SEMIRIGID COPPER TUBING |
| 89 | TABLE 402.4(10) SEMIRIGID COPPER TUBING |
| 90 | TABLE 402.4(11) SEMIRIGID COPPER TUBING |
| 91 | TABLE 402.4(12) SEMIRIGID COPPER TUBING |
| 92 | TABLE 402.4(13) SEMIRIGID COPPER TUBING |
| 93 | TABLE 402.4(14) SEMIRIGID COPPER TUBING |
| 94 | TABLE 402.4(15) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 95 | TABLE 402.4(16) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 96 | TABLE 402.4(17) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 97 | TABLE 402.4(18) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 98 | TABLE 402.4(19) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 99 | TABLE 402.4(20) POLYETHYLENE PLASTIC PIPE |
| 100 | TABLE 402.4(21) POLYETHYLENE PLASTIC PIPE |
| 101 | TABLE 402.4(22) POLYETHYLENE PLASTIC PIPE |
| 102 | TABLE 402.4(23) POLYETHYLENE PLASTIC TUBING TABLE 402.4(24) POLYETHYLENE PLASTIC TUBING |
| 103 | TABLE 402.4(25) SCHEDULE 40 METALLIC PIPE |
| 104 | TABLE 402.4(26) SCHEDULE 40 METALLIC PIPE |
| 105 | TABLE 402.4(27) SCHEDULE 40 METALLIC PIPE |
| 106 | TABLE 402.4(28) SCHEDULE 40 METALLIC PIPE |
| 107 | TABLE 402.4(29) SEMIRIGID COPPER TUBING |
| 108 | TABLE 402.4(30) SEMIRIGID COPPER TUBING |
| 109 | TABLE 402.4(31) SEMIRIGID COPPER TUBING |
| 110 | TABLE 402.4(32) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 111 | TABLE 402.4(33) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 112 | TABLE 402.4(34) CORRUGATED STAINLESS STEEL TUBING (CSST) |
| 113 | TABLE 402.4(35) POLYETHYLENE PLASTIC PIPE |
| 114 | TABLE 402.4(36) POLYETHYLENE PLASTIC PIPE |
| 115 | TABLE 402.4(37) POLYETHYLENE PLASTIC TUBING |
| 116 | SECTION 403 (IFGS) PIPING MATERIALS |
| 117 | TABLE 403.9.2 SPECIFICATIONS FOR THREADING METALLIC PIPE |
| 118 | SECTION 404 (IFGC) PIPING SYSTEM INSTALLATION |
| 120 | SECTION 405 (IFGS) PIPING BENDS AND CHANGES IN DIRECTION |
| 121 | SECTION 406 (IFGS) INSPECTION, TESTING AND PURGING |
| 122 | TABLE 406.7.1.1 SIZE AND LENGTH OF PIPING |
| 123 | SECTION 407 (IFGC) PIPING SUPPORT SECTION 408 (IFGC) DRIPS AND SLOPED PIPING FIGURE 408.4 METHOD OF INSTALLING A TEE FITTING SEDIMENT TRAP SECTION 409 (IFGC) SHUTOFF VALVES |
| 124 | TABLE 409.1.1 MANUAL GAS VALVE STANDARDS SECTION 410 (IFGC) FLOW CONTROLS |
| 125 | SECTION 411 (IFGC) APPLIANCE AND MANUFACTURED HOME CONNECTIONS |
| 126 | SECTION 412 (IFGC) LIQUEFIED PETROLEUM GAS MOTOR VEHICLE FUEL-DISPENSING FACILITIES |
| 127 | SECTION 413 (IFGC) COMPRESSED NATURAL GAS MOTOR VEHICLE FUEL-DISPENSING FACILITIES |
| 129 | [F] TABLE 413.9.2.3 SEPARATION DISTANCE FOR ATMOSPHERIC VENTING OF CNG SECTION 414 (IFGC) SUPPLEMENTAL AND STANDBY GAS SUPPLY SECTION 415 (IFGS) PIPING SUPPORT INTERVALS TABLE 415.1 SUPPORT OF PIPING SECTION 416 (IFGS) OVERPRESSURE PROTECTION DEVICES |
| 132 | CHAPTER 5 CHIMNEYS AND VENTS SECTION 501 (IFGC) GENERAL |
| 133 | SECTION 502 (IFGC) VENTS |
| 134 | SECTION 503 (IFGS) VENTING OF APPLIANCES |
| 135 | TABLE 503.4 TYPE OF VENTING SYSTEM TO BE USED |
| 137 | FIGURE 503.6.4 TERMINATION LOCATIONS FOR GAS VENTS WITH LISTED CAPS 12 INCHES OR LESS IN SIZE AT LEAST 8 FEET FROM A VERTICAL WALL |
| 140 | TABLE 503.10.2.4 MINIMUM THICKNESS FOR GALVANIZED STEEL VENT CONNECTORS FOR LOW-HEAT APPLIANCES TABLE 503.10.2.5 MINIMUM THICKNESS FOR STEEL VENT CONNECTORS FOR MEDIUM-HEAT APPLIANCES |
| 141 | TABLE 503.10.5a CLEARANCES FOR CONNECTORS |
| 143 | SECTION 504 (IFGS) SIZING OF CATEGORY I APPLIANCE VENTING SYSTEMS |
| 145 | TABLE 504.3.2 MAXIMUM VENT CONNECTOR LENGTH |
| 147 | SECTION 505 (IFGC) DIRECT-VENT, INTEGRAL VENT, MECHANICAL VENT AND VENTILATION/EXHAUST HOOD VENTING SECTION 506 (IFGC) FACTORY-BUILT CHIMNEYS |
| 148 | TABLE 504.2(1) TYPE B DOUBLE-WALL GAS VENT |
| 149 | TABLE 504.2(1)—continued TYPE B DOUBLE-WALL GAS VENT |
| 150 | TABLE 504.2(1)—continued TYPE B DOUBLE-WALL GAS VENT |
| 151 | TABLE 504.2(1)—continued TYPE B DOUBLE-WALL GAS VENT |
| 152 | TABLE 504.2(2) TYPE B DOUBLE-WALL GAS VENT |
| 153 | TABLE 504.2(2)-continued TYPE B DOUBLE-WALL GAS VENT |
| 154 | TABLE 504.2(3) MASONRY CHIMNEY |
| 155 | TABLE 504.2(3)—continued MASONRY CHIMNEY |
| 156 | TABLE 504.2(4) MASONRY CHIMNEY |
| 157 | TABLE 504.2(4)—continued MASONRY CHIMNEY |
| 158 | TABLE 504.2(5) SINGLE-WALL METAL PIPE OR TYPE B ASBESTOS CEMENT VENT |
| 159 | TABLE 504.2(6) EXTERIOR MASONRY CHIMNEY |
| 160 | TABLE 504.3(1) TYPE B DOUBLE-WALL VENT |
| 161 | TABLE 504.3(1)-continued TYPE B DOUBLE-WALL VENT |
| 162 | TABLE 504.3(2) TYPE B DOUBLE-WALL VENT |
| 163 | TABLE 504.3(3) MASONRY CHIMNEY |
| 164 | TABLE 504.3(4) MASONRY CHIMNEY |
| 165 | TABLE 504.3(5) SINGLE-WALL METAL PIPE OR TYPE ASBESTOS CEMENT VENT |
| 166 | TABLE 504.3(6a) EXTERIOR MASONRY CHIMNEY TABLE 504.3(6b) EXTERIOR MASONRY CHIMNEY TABLE 504.3(6b) EXTERIOR MASONRY CHIMNEY-continued |
| 167 | TABLE 504.3(7a) EXTERIOR MASONRY CHIMNEY TABLE 504.3(7b) EXTERIOR MASONRY CHIMNEY TABLE 504.3(7b) EXTERIOR MASONRY CHIMNEY—continued |
| 168 | CHAPTER 6 SPECIFIC APPLIANCES SECTION 601 (IFGC) GENERAL SECTION 602 (IFGC) DECORATIVE APPLIANCES FOR INSTALLATION IN FIREPLACES SECTION 603 (IFGC) LOG LIGHTERS SECTION 604 (IFGC) VENTED GAS FIREPLACES (DECORATIVE APPLIANCES) SECTION 605 (IFGC) VENTED GAS FIREPLACE HEATERS SECTION 606 (IFGC) INCINERATORS AND CREMATORIES SECTION 607 (IFGC) COMMERCIAL-INDUSTRIAL INCINERATORS SECTION 608 (IFGC) VENTED WALL FURNACES |
| 169 | SECTION 609 (IFGC) FLOOR FURNACES SECTION 610 (IFGC) DUCT FURNACES SECTION 611 (IFGC) NONRECIRCULATING DIRECT-FIRED INDUSTRIAL AIR HEATERS |
| 170 | SECTION 612 (IFGC) RECIRCULATING DIRECT-FIRED INDUSTRIAL AIR HEATERS SECTION 613 (IFGC) CLOTHES DRYERS SECTION 614 (IFGC) CLOTHES DRYER EXHAUST |
| 171 | [M] TABLE 614.8.4.1 DRYER EXHAUST DUCT FITTING EQUIVALENT LENGTH |
| 172 | SECTION 615 (IFGC) SAUNA HEATERS |
| 173 | SECTION 616 (IFGC) ENGINE AND GAS TURBINE-POWERED EQUIPMENT SECTION 617 (IFGC) POOL AND SPA HEATERS SECTION 618 (IFGC) FORCED-AIR WARM-AIR FURNACES |
| 174 | SECTION 619 (IFGC) CONVERSION BURNERS SECTION 620 (IFGC) UNIT HEATERS SECTION 621 (IFGC) UNVENTED ROOM HEATERS |
| 175 | SECTION 622 (IFGC) VENTED ROOM HEATERS SECTION 623 (IFGC) COOKING APPLIANCES SECTION 624 (IFGC) WATER HEATERS SECTION 625 (IFGC) REFRIGERATORS SECTION 626 (IFGC) GAS-FIRED TOILETS |
| 176 | SECTION 627 (IFGC) AIR-CONDITIONING APPLIANCES SECTION 628 (IFGC) ILLUMINATING APPLIANCES |
| 177 | SECTION 629 (IFGC) SMALL CERAMIC KILNS SECTION 630 (IFGC) INFRARED RADIANT HEATERS SECTION 631 (IFGC) BOILERS SECTION 632 (IFGC) EQUIPMENT INSTALLED IN EXISTING UNLISTED BOILERS SECTION 633 (IFGC) STATIONARY FUEL-CELL POWER SYSTEMS TABLE 634.1 FREE OPENING AREA OF CHIMNEY DAMPER FOR VENTING FLUE GASES FROM UNLISTED DECORATIVE APPLIANCES FOR INSTALLATION IN VENTED FIREPLACES |
| 178 | SECTION 634 (IFGS) CHIMNEY DAMPER OPENING AREA SECTION 635 (IFGC) GASEOUS HYDROGEN SYSTEMS SECTION 636 (IFGC) OUTDOOR DECORATIVE APPLIANCES |
| 180 | CHAPTER 7 GASEOUS HYDROGEN SYSTEMS SECTION 701 (IFGC) GENERAL SECTION 702 (IFGC) GENERAL DEFINITIONS SECTION 703 (IFGC) GENERAL REQUIREMENTS |
| 181 | SECTION 704 (IFGC) PIPING, USE AND HANDLING |
| 182 | SECTION 705 (IFGC) TESTING OF HYDROGEN PIPING SYSTEMS |
| 183 | SECTION 706 (IFGC) LOCATION OF GASEOUS HYDROGEN SYSTEMS |
| 184 | SECTION 707 (IFGC) OPERATION AND MAINTENANCE OF GASEOUS HYDROGEN SYSTEMS SECTION 708 (IFGC) DESIGN OF LIQUEFIED HYDROGEN SYSTEMS ASSOCIATED WITH HYDROGEN VAPORIZATION OPERATIONS |
| 186 | IFGC/IFGS CHAPTER 8 REFERENCED STANDARDS ANSI |
| 187 | ASME ASTM CGA |
| 188 | CSA DOTn ICC MSS |
| 189 | NFPA UL |
| 190 | APPENDIX A (IFGS) SIZING AND CAPACITIES OF GAS PIPING A.1 GENERAL PIPING CONSIDERATIONS A.2 DESCRIPTION OF TABLES |
| 191 | TABLE A.2.2 EQUIVALENT LENGTHS OF PIPE FITTINGS AND VALVES |
| 192 | TABLE A.2.2—continued EQUIVALENT LENGTHS OF PIPE FITTINGS AND VALVES |
| 193 | TABLE A.2.4 MULTIPLIERS TO BE USED WITH TABLES 402.4(1) THROUGH 402.4(22) WHERE THE SPECIFIC GRAVITY OF THE GAS IS OTHER THAN 0.60 A.3 USE OF CAPACITY TABLES |
| 195 | TABLE A.3.4 THOUSANDS OF BTU/H (MBH) OF NATURAL GAS PER 100 FEET OF PIPE AT VARIOUS PRESSURE DROPS AND PIPE DIAMETERS A.4 USE OF SIZING EQUATIONS |
| 196 | A.5 PIPE AND TUBE DIAMETERS TABLE A.5.1 SCHEDULE 40 STEEL PIPE STANDARD SIZES TABLE A.5.2 COPPER TUBE STANDARD SIZES A.6 EXAMPLES OF PIPING SYSTEM DESIGN AND SIZING |
| 197 | FIGURE A.6.1 PIPING PLAN SHOWING A STEEL PIPING SYSTEM FIGURE A.6.2 PIPING PLAN SHOWING A CSST SYSTEM |
| 198 | FIGURE A.6.3 PIPING PLAN SHOWING A COPPER TUBING SYSTEM |
| 199 | FIGURE A.6.4 PIPING PLAN SHOWING A MODIFICATION TO EXISTING PIPING SYSTEM |
| 202 | APPENDIX B (IFGS) SIZING OF VENTING SYSTEMS SERVING APPLIANCES EQUIPPED WITH DRAFT HOODS, CATEGORY I APPLIANCES AND APPLIANCES LISTED FOR USE WITH TYPE B VENTS EXAMPLES USING SINGLE APPLIANCE VENTING TABLES FIGURE B-1 TYPE B DOUBLE-WALL VENT SYSTEM SERVING A SINGLE APPLIANCE WITH A TYPE B DOUBLE-WALL VENT FIGURE B-2 TYPE B DOUBLE-WALL VENT SYSTEM SERVING A SINGLE APPLIANCE WITH A SINGLE-WALL METAL VENT CONNECTOR |
| 203 | FIGURE B-3 VENT SYSTEM SERVING A SINGLE APPLIANCE WITH A MASONRY CHIMNEY OF TYPE B DOUBLE-WALL VENT CONNECTOR FIGURE B-4 VENT SYSTEM SERVING A SINGLE APPLIANCE USING A MASONRY CHIMNEY AND A SINGLE-WALL METAL VENT CONNECTOR FIGURE B-5 ASBESTOS CEMENT TYPE B OR SINGLE-WALL METAL VENT SYSTEM SERVING A SINGLE DRAFT-HOOD-EQUIPPED APPLIANCE FIGURE B-6 VENT SYSTEM SERVING TWO OR MORE APPLIANCES WITH TYPE B DOUBLE-WALL VENT AND TYPE B DOUBLE-WALL VENT CONNECTOR |
| 204 | FIGURE B-7 VENT SYSTEM SERVING TWO OR MORE APPLIANCES WITH TYPE B DOUBLE-WALL VENT AND SINGLE-WALL METAL VENT CONNECTORS FIGURE B-8 MASONRY CHIMNEY SERVING TWO OR MORE APPLIANCES WITH TYPE B DOUBLE-WALL VENT CONNECTOR FIGURE B-9 MASONRY CHIMNEY SERVING TWO OR MORE APPLIANCES WITH SINGLE-WALL METAL VENT CONNECTORS FIGURE B-10 ASBESTOS CEMENT TYPE B OR SINGLE-WALL METAL VENT SYSTEM SERVING TWO OR MORE DRAFT-HOOD-EQUIPPED APPLIANCES |
| 205 | FIGURE B-11 USE OF MANIFOLD COMMON VENT CONNECTOR FIGURE B-12 USE OF OFFSET COMMON VENT FIGURE B-13 MULTISTORY GAS VENT DESIGN PROCEDURE FOR EACH SEGMENT OF SYSTEM FIGURE B-14 MULTISTORY VENT SYSTEMS |
| 206 | FIGURE B-15 (EXAMPLE 1) SINGLE DRAFT-HOOD-EQUIPPED APPLIANCE FIGURE B-16 (EXAMPLE 2) SINGLE FAN-ASSISTED APPLIANCE |
| 207 | EXAMPLES USING COMMON VENTING TABLES FIGURE B-17 (EXAMPLE 4) COMMON VENTING TWO DRAFT-HOOD-EQUIPPED APPLIANCES FIGURE B-18 (EXAMPLE 5A) COMMON VENTING A DRAFT HOOD WITH A FAN-ASSISTED FURNACE INTO A TYPE B DOUBLE-WALL COMMON VENT |
| 209 | TABLE B-1 MASONRY CHIMNEY LINER DIMENSIONS WITH CIRCULAR EQUIVALENTSa |
| 210 | FIGURE B-19 |
| 212 | APPENDIX C (IFGS) EXIT TERMINALS OF MECHANICAL DRAFT AND DIRECT-VENT VENTING SYSTEMS APPENDIX C EXIT TERMINALS OF MECHANICAL DRAFT AND DIRECT-VENT VENTING SYSTEMS |
| 214 | APPENDIX D (IFGS) RECOMMENDED PROCEDURE FOR SAFETY INSPECTION OF AN EXISTING APPLIANCE INSTALLATION D.1 GENERAL D.2 OCCUPANT AND INSPECTOR SAFETY |
| 215 | D.3 GAS PIPING AND CONNECTION INSPECTIONS D.4 INSPECTIONS TO BE PERFORMED WITH THE APPLIANCE NOT OPERATING |
| 216 | D.5 INSPECTIONS TO BE PERFORMED WITH THE APPLIANCE OPERATING |
| 217 | D.6 APPLIANCE-SPECIFIC INSPECTIONS |
| 219 | TABLE D.6 CO THRESHOLDS |
| 220 | INDEX |
| 224 | ICC EVALUATION SERVICE |
| 225 | ICC LEARNING CENTER |
| 226 | ICC ASSESSMENT CENTER |
| 227 | ICC MEMBERSHIP |
