AGMA 01FTM09:2001 Edition
$14.30
New Opportunities with Molded Gears
| Published By | Publication Date | Number of Pages |
| AGMA | 2001 | 11 |
Unique tooth geometry that might be difficult or even impossible to achieve with cut gears can be applied to molded gears. This paper will investigate two types of gears that have been designed, molded and tested in plastic. The first is an asymmetric mesh with dissimilar 23 and 35 degree pressure angles. The second is an orbiting transmission with a 65 degree pressure angle. Both transmissions have higher load potential than traditional design approaches.
Related products
-
AGMA 08FTM02:2008 Edition
A Methodology for Identifying Defective Cycloidal Reduction Components Using Vibration Analysis and Techniques Published By…
-
AGMA 05FTM09:2005 Edition
Hypoid Gear Lapping Wear Coefficient and Simulation Published By Publication Date Number of Pages AGMA…
-
AGMA 09FTM19:2009 Edition
The Effect of Gearbox Architecture on Wind Turbine Enclosure Size Published By Publication Date Number…
-
AGMA 10FTM04:2010 Edition
Low Distortion Heat Treatment of Transmission Components Published By Publication Date Number of Pages AGMA…
-
AGMA 01FTM03:2001 Edition
Automated Spiral Bevel Gear Pattern Inspection Published By Publication Date Number of Pages AGMA 2001…
-
AGMA 10FTM09:2010 Edition
Reverse Engineering Published By Publication Date Number of Pages AGMA 2010 9
-
AGMA 94FTM09:1994 Edition
Analytical and Experimental Vibration Analysis of a Damaged Gear Published By Publication Date Number of…
-
AGMA 09FTM09:2009 Edition
Designing for Static and Dynamic Loading of a Gear Reducer Housing with FEA Published By…
-
AGMA 10FTM08:2010 Edition
Calculation of Load Distribution in Planetary Gears for an Effective Gear Design Process Published By…
-
AGMA 12FTM09:2012 Edition
Systematic Approach for the Psychoacoustic Analysis of Dynamic Gear Noise Excitation Published By Publication Date…
-
AGMA 08FTM08:2008 Edition
PM Materials for Gear Applications Published By Publication Date Number of Pages AGMA 2008 9
-
AGMA 91FTM09:1991 Edition
Rerating Damaged Naval Ship Propulsion Gear Published By Publication Date Number of Pages AGMA 1991…
-
AGMA 05FTM08:2005 Edition
New Developments in Tooth Contact Analysis (TCA) and Loaded TCA for Spiral Bevel and Hypoid…
-
AGMA 01FTM02:2001 Edition
The Ultimate Motion Graph for “Noiseless” Gears Published By Publication Date Number of Pages AGMA…
-
AGMA 06FTM09:2006 Edition
Opportunities to Replace Wrought Gears with High Performance PM Gears in Automotive Applications Published By…
-
AGMA 05FTM06:2005 Edition
A Model to Predict Friction Losses of Hypoid Gears Published By Publication Date Number of…
-
AGMA 04FTM02:2004 Edition
Noise Optimized Modifications: Renaissance of the Generating Grinders? Published By Publication Date Number of Pages…
-
AGMA 01FTM01:2001 Edition
Carbide Hobbing Case Study Published By Publication Date Number of Pages AGMA 2001 16
-
AGMA 01FTM08:2001 Edition
The Effect of Spacing Errors and Runout on Transverse Load Sharing and the Dynamic Factor…
-
AGMA 01FTM07:2001 Edition
Chemically Accelerated Vibratory Finishing for the Elimination of Wear and Pitting of Alloy Steel Gears…
-
AGMA 09FTM06:2009 Edition
Dependency of the Peak-to-Peak Transmission Error on the Type of Profile Correction and Transverse Contact…
-
AGMA 02FTM09:2002 Edition
Gear RollScan for High-Speed Gear Measurement Published By Publication Date Number of Pages AGMA 2002…
-
AGMA 04FTM09:2004 Edition
Design of a High Ratio, Ultra Safe, High Contact Ratio, Double Helical Compound Planetary Transmission…
-
AGMA 09FTM08:2009 Edition
Load Sharing Analysis of High Contact Ratio Spur Gears in Military Tracked Vehicle Application Published…
-
AGMA 10FTM01:2010 Edition
Complete Machining of Gear Blank and Gear Teeth Published By Publication Date Number of Pages…
-
AGMA 91FTM07:1991 Edition
Low Cycle and Static Bending Strength of Carburized and High Hardness Through Hardened Gear Teeth…
-
AGMA 01FTM05:2001 Edition
Traceability of Gears, New Ideas, Recent Developments Published By Publication Date Number of Pages AGMA…
-
AGMA 01FTMS1:2001 Edition
Optical Technique for Gear Contouring Published By Publication Date Number of Pages AGMA 2001 12
-
AGMA 01FTM04:2001 Edition
How to Inspect Large Cylindrical Gears with an Outside Diameter of more than 40 Inches…
-
AGMA 91FTM05:1991 Edition
Machine Tool Condition Monitoring Published By Publication Date Number of Pages AGMA 1991 8
-
AGMA 91FTM06:1991 Edition
Comparing Surface Failure Modes in Bearings and Gears: Appearances versus Mechanisms Published By Publication Date…
-
AGMA 09FTM05:2009 Edition
HYPOLOID Gears with Small Shaft Angles and Zero to Large Offsets Published By Publication Date…
-
AGMA 07FTM09:2007 Edition
The Ikona Clutch and Differential Published By Publication Date Number of Pages AGMA 2007 8
-
AGMA 01FTM06:2001 Edition
Performance-Based Gear-Error Inspection, Specification, and Manufacturing-Source Diagnostics Published By Publication Date Number of Pages AGMA…
-
AGMA 08FTM09:2008 Edition
Concept for a Multi Megawatt Wind Turbine Gear and Field Experience Published By Publication Date…
-
AGMA 09FTM03:2009 Edition
Producing Profile and Lead Modifications in Threaded Wheel and Profile Grinding Published By Publication Date…
-
AGMA 04FTM08:2004 Edition
Generalized Excitation of Traveling Wave Vibration in Gears Published By Publication Date Number of Pages…
-
AGMA 09FTM01:2009 Edition
Influence of the Residual Stresses Induced by Hard Finishing Processes on the Running Behavior of…
-
AGMA 07FTM01:2007 Edition
Estimation of Lifetime of Plastic Gears Published By Publication Date Number of Pages AGMA 2007…
-
AGMA 05FTM05:2005 Edition
Computerized Design of Face Hobbed Hypoid Gears: Tooth Surface Generation, Contact Analysis and Stress Calculation…
