🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
ASTM-A1022:2007 Edition(Redline)

ASTM-A1022:2007 Edition(Redline)

$26.65

A1022/A1022M-07 Standard Specification for Deformed and Plain Stainless Steel Wire and Welded Wire for Concrete Reinforcement (Redline)

Published By Publication Date Number of Pages
ASTM 2007 11
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Abstract

This specification covers stainless steel wire and welded wire reinforcements from hot-rolled stainless steel rod to be used as concrete reinforcement with corrosion resistant and magnetic permeability properties. The material shall be cold-worked, drawn or rolled, and plain or deformed. Materials shall adhere to deformation requirements. Tensile, yield, and weld shear strengths shall be measured. Bend tests shall also be performed. Dimensional requirements and permissible variations in width, length, weight, density, cross-sectional area, diameter, and average spacings of wires are specified. Guidelines for sampling, inspection, rejection, retest, certification, and packaging are given.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers stainless steel wire and welded wire reinforcement produced from hot-rolled stainless steel rod. The stainless steel wire is cold-worked, drawn or rolled, plain (non-deformed) or deformed or a combination of deformed and plain. It is used as concrete reinforcement for applications requiring resistance to corrosion and/or controlled magnetic permeability. Common wire sizes and dimensions are found in this specification. Actual wire sizes are not restricted to those shown in the tables.

1.2 Supplement S1 describes high strength wire, which shall be furnished when specifically ordered. It shall be permissible to furnish high strength wire in place of regular wire if mutually agreed to by the purchaser and supplier.

1.2.1 A supplementary requirement (S2) of an optional nature is provided. It shall apply only when specified by the purchaser. In order to obtain a corrosion tested or controlled magnetic permeability product, steel conforming to Supplementary Requirement S2 should be ordered.

1.3 The chemical composition of the steel (stainless grade) shall be selected for suitability to the application involved by agreement between the manufacturer and the purchaser. Use Specification A 276 for chemical requirements. The UNS designations are to be included with the type number and noted in brackets, i.e. austenitic stainless steels as Type 304 [S30400], 304L [S30403], 316 [S31600], 316L [S31603], 316N [S31651], 316LN [S31653] and duplex stainless steels, Types 2205 [S32205] and 329 [S32900].

Note 1

Only austenitic and duplex stainless steels are usually recommended for use as reinforcement in concrete because of their high corrosion resistance. Austenitic stainless steels have good general corrosion resistance, strength characteristics which can be improved by cold working, good toughness and ductility properties at low temperatures, and low magnetic permeability. Duplex stainless steels have generally a corrosion resistance greater than that of most austenitic steels and are magnetic. Other stainless steels with different chemical compositions than the series and types mentioned above, may be used for less restrictive applications.

1.4 Wire for welded wire reinforcement is generally manufactured at 520 MPa [75 ksi] yield strength level. Other strength levels shall be by agreement between the purchaser and manufacturer.

Note 2

The term used to refer to yield strength levels are the same as those in ASTM Standards for welded wire reinforcement.

1.5 The values stated in SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A82/A82M Specification for Steel Wire, Plain, for Concrete Reinforcement A185/A185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete A276 Specification for Stainless Steel Bars and Shapes A342/A342M Test Methods for Permeability of Feebly Magnetic Materials A370 Test Methods and Definitions for Mechanical Testing of Steel Products A496/A496M Specification for Steel Wire, Deformed, for Concrete Reinforcement A497/A497M Specification for Steel Welded Wire Reinforcement, Deformed, for Concrete A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment E83 Practice for Verification and Classification of Extensometer Systems

Military Standards

MIL-STD-129 Marking for Shipment and Storage

Federal Standard

Fed. Std.  Marking for Shipments (Civil Agencies)

ACI Standard

ACI 318 Building Code Requirements for Structural Concrete

Keywords

concrete reinforcement; corrosion resistance; deformations; magnetic properties; reinforced concrete; reinforcing steels; stainless steel welded wire reinforcement; stainless wire; steel wire; welded wire reinforcement;

Related products

ASTM-A1022
$26.65