ASTM-A6 2012

$67.71

A6/A6M-12 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

Published By	Publication Date	Number of Pages
ASTM	2012	63

Guaranteed Safe Checkout

Categories: 77.140.60 - Steel bars and rods, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

1.1 This general requirements specification covers a group of common requirements that, unless otherwise specified in the applicable product specification, apply to rolled structural steel bars, plates, shapes, and sheet piling covered by each of the following product specifications issued by ASTM:

1.2 Annex A1 lists permitted variations in dimensions and mass (Note 1) in SI units. The values listed are not exact conversions of the values in Tables 1 to 31 inclusive but are, instead, rounded or rationalized values. Conformance to Annex A1 is mandatory when the M specification designation is used.

Note 1The term weight is used when inch-pound units are the standard; however, under SI, the preferred term is mass.

1.3 Annex A2 lists the dimensions of some shape profiles.

1.4 Appendix X1 provides information on coil as a source of structural products.

1.5 Appendix X2 provides information on the variability of tensile properties in plates and structural shapes.

1.6 Appendix X3 provides information on weldability.

1.7 Appendix X4 provides information on cold bending of plates, including suggested minimum inside radii for cold bending.

1.8 This general requirements specification also covers a group of supplementary requirements that are applicable to several of the above product specifications as indicated therein. Such requirements are provided for use where additional testing or additional restrictions are required by the purchaser, and apply only where specified individually in the purchase order.

1.9 In case of any conflict in requirements, the requirements of the applicable product specification prevail over those of this general requirements specification.

1.10 Additional requirements that are specified in the purchase order and accepted by the supplier are permitted, provided that such requirements do not negate any of the requirements of this general requirements specification or the applicable product specification.

1.11 For purposes of determining conformance with this general requirements specification and the applicable product specification, values are to be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29 .

1.12 The text of this general requirements specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.

1.13 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way.

1.14 This general requirements specification and the applicable product specification are expressed in both inch-pound units and SI units; however, unless the order specifies the applicable M specification designation (SI units), the structural product is furnished to inch-pound units.

1.15 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

PDF Catalog

PDF Pages	PDF Title
1	Scope
2	Referenced Documents Terminology
4	Ordering Information Materials and Manufacture Heat Treatment
5	Chemical Analysis Metallurgical Structure Quality
6	TABLE
8	Test Methods Tension Tests
10	TABLE TABLE
11	Permitted Variations in Dimensions and Weight [Mass]
12	Retests Test Reports
13	Inspection and Testing Retreatment Rejection Identification of Structural Products
14	Packaging, Marking, and Loading for Shipment Keywords
15	TABLE 1 TABLE 2
16	TABLE 3 TABLE 4 TABLE 5
17	TABLE 6 TABLE 7 TABLE 8 TABLE 9 TABLE 10 TABLE 11 TABLE 12
18	TABLE 13 TABLE 14
19	TABLE 15
20	TABLE 16
21	TABLE 17 TABLE 18
22	TABLE 19 TABLE 20
23	TABLE 21 TABLE 22 TABLE 23
24	TABLE 24 TABLE 25
25	TABLE 26 TABLE 27 TABLE 28 TABLE 29
26	TABLE 30 TABLE 31
27	TABLE S27.1
28	TABLE S27.2 TABLE S27.3
29	TABLE S27.4
31	A1. PERMITTED VARIATIONS IN DIMENSIONS AND MASS IN SI UNITS A1.1 TABLE A1.1
32	TABLE A1.2
33	TABLE A1.3 TABLE A1.4 TABLE A1.5
34	TABLE A1.6 TABLE A1.7 TABLE A1.8 TABLE A1.9
35	TABLE A1.10 TABLE A1.11 TABLE A1.12 TABLE A1.13
36	TABLE A1.14
37	TABLE A1.15
38	TABLE A1.16
39	TABLE A1.17 TABLE A1.18
40	TABLE A1.19 TABLE A1.20
41	TABLE A1.21 TABLE A1.22
42	TABLE A1.23 TABLE A1.24 TABLE A1.25
43	TABLE A1.26 TABLE A1.27 TABLE A1.28 TABLE A1.29
44	A2. DIMENSIONS OF STANDARD SHAPE PROFILES A2.1 TABLE A2.1 TABLE A1.30 TABLE A1.31
50	TABLE A2.2
51	TABLE A2.3
52	TABLE A2.4
53	TABLE A2.5
54	TABLE A2.6
56	TABLE A2.7
58	TABLE A2.8
60	X1. COIL AS A SOURCE OF STRUCTURAL PRODUCTS X1.1 X2. VARIATION OF TENSILE PROPERTIES IN PLATES AND SHAPES X2.1 X2.2 X2.3 X2.4 X2.5
61	X3. WELDABILITY OF STEEL X3.1 X3.2 X3.3 X3.4 X3.5 X3.6 X4. RADIUS FOR COLD BENDING X4.1 X4.2
62	X4.3 References TABLE X4.1 TABLE X4.2

Additional information

A572/A572M	High-Strength Low-Alloy Columbium-Vanadium Steel
A769/A769M	Carbon and High-Strength Electric Resistance Welded Steel Structural Shapes
A709/A709M	Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges
A852/A852M	Quenched and Tempered Low-Alloy Structural Steel Plate with 70 ksi [485 Mpa] Minimum Yield Strength to 4 in. [100 mm] Thick
A871/A871M	High-Strength Low Alloy Structural Steel Plate with Atmospheric Corrosion Resistance
A588/A588M	High-Strength Low-Alloy Structural Steel with 50 ksi (345 MPa) Minimum Yield Point to 4 in. [100 mm] Thick
A656/A656M	Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability
A945/A945M	Specification for High-Strength Low-Alloy Structural Steel Plate with Low Carbon and Restricted Sulfur for Improved Weldability, Formability, and Toughness
A633/A633M	Normalized High-Strength Low-Alloy Structural Steel Plates
A786/A786M	Rolled Steel Floor Plates
A131/A131M	Structural Steel for Ships
A830/A830M	Plates, Carbon Steel, Structural Quality, Furnished to Chemical Composition Requirements
A690/A690M	High-Strength Low-Alloy Steel H-Piles and Sheet Piling for Use in Marine Environments
A283/A283M	Low and Intermediate Tensile Strength Carbon Steel Plates
A1043/A1043M	Specification for Structural Steel with Low Yield to Tensile Ratio for Use in Buildings
A710/A710M	Age-Hardening Low-Carbon Nickel-Copper-Chromium-Mo- lybdenum-Columbium Alloy Structural Steel Plates
A529/A529M	High-Strength Carbon-Manganese Steel of Structural Quality
ASTM Designation 3	Title of Specification
A1026	Specification for Alloy Steel Structural Shapes for Use in Building Framing
A992/A992M	Specification for Steel for Structural Shapes for Use in Building Framing
A913/A913M	Specification for High-Strength Low-Alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-Tempering Process (QST)
A829/A829M	Plates, Alloy Steel, Structural Quality
A242/A242M	High-Strength Low-Alloy Structural Steel
A808/A808M	High-Strength Low-Alloy Carbon, Manganese, Columbium, Vanadium Steel of Structural Quality with Improved Notch Toughness
A678/A678M	Quenched-and-Tempered Carbon and High-Strength Low-Alloy Structural Steel Plates
A857/A857M	Steel Sheet Piling, Cold Formed, Light Gage
A827/A827M	Plates, Carbon Steel, for Forging and Similar Applications
A36/A36M	Carbon Structural Steel
A514/A514M	High-Yield Strength, Quenched and Tempered Alloy Steel Plate Suitable for Welding
A950/A950M	Specification for Fusion Bonded Epoxy-Coated Structural Steel H-Piles and Sheet Piling
A573/A573M	Structural Carbon Steel Plates of Improved Toughness
ICS Codes	77.140.60 - Steel bars and rods
A328/A328M	Steel Sheet Piling

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-A6 2012

PDF Catalog

Related products