ASTM-B353 2007
$44.96
B353-07 Standard Specification for Wrought Zirconium and Zirconium Alloy Seamless and Welded Tubes for Nuclear Service (Except Nuclear Fuel Cladding)
| Published By | Publication Date | Number of Pages |
| ASTM | 2007 | 18 |
1.1 This specification covers seamless and welded wrought zirconium and zirconium-alloy tubes for nuclear application. Nuclear fuel cladding is covered in Specification B 811.
1.2 Five grades of reactor grade zirconium and zirconium alloys suitable for nuclear application are described.
1.2.1 The present UNS numbers designated for the five grades are given in Table 1.
1.3 Unless a single unit is used, for example corrosion mass gain in mg/dm 2 , the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.
1.4 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | Scope Referenced Documents Terminology TABLE 1 |
| 2 | Ordering Information TABLE 2 |
| 3 | Materials and Manufacture Condition and Finish Chemical Composition TABLE 3 |
| 4 | Mechanical Properties TABLE 4 TABLE 5 |
| 5 | Grain Size Corrosion Properties Inspection |
| 6 | Hydride Orientation Hydrostatic Test Number of Tests Retest |
| 7 | Significance of Numerical Limits Quantity Variance Rejection Certification Packaging and Package Marking Referee Keywords A1. RECOMMENDED CLOSED-END BURST TESTING PROCEDURE FOR ZIRCONIUM ALLOY TUBING A1.1 Scope A1.2 Apparatus |
| 8 | A1.3 Preparation of Specimen A1.4 Procedure A1.5 Report A2. RECOMMENDED PROCEDURE FOR DETERMINATION OF HYDRIDE ORIENTATION IN ZIRCONIUM-ALLOY TUBING A2.1 Test Criteria A2.2 Procedure A2.3 Measurement |
| 9 | A3. RECOMMENDED PROCEDURE FOR ULTRASONIC TESTING OF ZIRCONIUM AND ZIRCONIUM ALLOY TUBING FOR NUCLEAR SERVICE A3.1 Scope A3.2 Terminology A3.3 Surface Condition A3.4 Apparatus |
| 10 | A3.5 Couplant A3.6 Calibration Standards FIG. A3.1 FIG. A3.2 FIG. A3.3 |
| 11 | A3.7 Calibration of the Apparatus A3.8 Inspection Procedure FIG. A3.4 |
| 12 | A3.9 Interpretation of Results FIG. A3.5 |
| 13 | A3.10 Report A4. RECOMMENDED PROCEDURE FOR CONTRACTILE STRAIN RATIO TESTING OF ZIRCONIUM ALLOY TUBING A4.1 Scope A4.2 Apparatus A4.3 Preparation of Specimen A4.4 Procedure A4.5 Calculation FIG. A4.1 |
| 14 | X1. AN ADVISORY GUIDE TO TRANSDUCER SELECTION X1.1 X1.2 X1.3 X1.4 Transducers for Shear-Wave Inspection FIG. X1.1 |
| 15 | X1.5 Transducers for Lamb-Wave Inspection X2. AN ADVISORY GUIDE TO TRANSDUCER POSITIONING X2.1 X2.2 Transducer Positioning for Shear Wave Testing FIG. X1.2 |
| 16 | X2.3 Transducer Positioning for Lamb Wave Inspection FIG. X2.1 |
| 17 | X3. RATIONALE (COMMENTARY) X3.1 X3.2 X3.3 X3.4 X3.5 X3.6 X3.7 X3.8 FIG. X2.2 FIG. X2.3 |
Related products
-
ASTM-B353 2007(Redline)
B353-07 Standard Specification for Wrought Zirconium and Zirconium Alloy Seamless and Welded Tubes for Nuclear…
