ASTM-B446 2023

$34.13

B446-23 Standard Specification for Nickel-Chromium-Molybdenum-Niobium Alloy, Nickel-Chromium-Molybdenum-Silicon Alloy, and Nickel-Chromium-Molybdenum-Tungsten Alloy Rod and Bar

Published By	Publication Date	Number of Pages
ASTM	2023	6

Guaranteed Safe Checkout

Categories: 77.150.40 - Nickel and chromium products, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM B446-23

Active Standard: Standard Specification for Nickel-Chromium-Molybdenum-Niobium Alloy, Nickel-Chromium-Molybdenum-Silicon Alloy, and Nickel-Chromium-Molybdenum-Tungsten Alloy Rod and Bar

ASTM B446

Scope

1.1 This specification covers nickel-chromium-molybdenum-niobium alloy (UNS N06625), nickel-chromium-molybdenum-silicon alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650)2 in the form of both hot-worked and cold-worked rod and bar in the conditions shown in Table 1.

1.1.1 UNS N06625 products are furnished in three grades of different heat-treated conditions:

1.1.1.1 Grade 1 (Annealed)—Material is normally employed in service temperatures up to 1100 °F (593 °C).

1.1.1.2 Grade 2 (Solution Annealed)—Material is normally employed in service temperatures above 1100 °F (593 °C) when resistance to creep and rupture is required.

Note 1: Hot-working or reannealing may change properties significantly, depending on working history and temperatures.

1.1.1.3 Grade 3 (Solution Annealed and Cold Worked)—Material is normally employed in services where higher strengths are needed.

1.1.2 Alloys UNS N06219 and UNS N06650 are supplied in solution annealed condition only.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following precautionary caveat pertains only to the test methods portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

bar; rod; UNS N06219; UNS N06625; UNS N06650;

ICS Code

ICS Number Code 77.150.40 (Nickel and chromium products)

DOI: 10.1520/B0446-23

Additional information

Standard Title	B446-23 Standard Specification for Nickel-Chromium-Molybdenum-Niobium Alloy, Nickel-Chromium-Molybdenum-Silicon Alloy, and Nickel-Chromium-Molybdenum-Tungsten Alloy Rod and Bar
Published Code	ASTM
Publication Date	2023
Pages Count	6
ICS Codes	77.150.40 - Nickel and chromium products