ASTM-B949 2008(Redline)

$26.65

B949-08 Standard Specification for General Requirements for Zinc and Zinc Alloy Products (Redline)

Published By	Publication Date	Number of Pages
ASTM	2008	6

Guaranteed Safe Checkout

Category: ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

Abstract

This specification establishes general requirements, unless otherwise specified in the specific product specification, for zinc and zinc alloy products. Final product (ingots, slabs, jumbos, etc.) shall conform to the chemical composition requirements prescribed in the applicable product specification. The determination of chemical composition shall be made in accordance with suitable spectrochemical or chemical methods. Methods of sampling for chemical analysis includes: (1) sampling during casting of ingots, slabs, blocks or jumbos, and wrought products, (2) sampling in the event of a dispute or if the alloy is at the customers plant, (3) sampling of zinc alloy ingots for routine testing, nominal quality, non-dispute situations, and (4) sampling of final product castings. Sampling may be done by sawing, milling, drilling, turning, or clipping. Color code requirements for the alloy are detailed.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification establishes general requirements, unless otherwise specified in the specific product specification, for ordering information, marking, and sampling for chemical analysis common to zinc and zinc alloy products and shall apply to Specifications B 6, B 69, B 86, B 240, B 327, B 418, B 750, B 792, B 793, B 833, B 852, B 860, B 892, B 894, B 897, B 907, and B 943 to the extent referenced therein.

1.2 Although this specification establishes general requirements, it does not restrict that, by agreement between customer and supplier, these requirements may be altered by a customer to suit individual need.

1.3 The chemical composition, physical and mechanical properties, and all other requirements not included in this specification shall be prescribed in the product specification.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. This applies except where SI units only are specified.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

B6 Specification for Zinc B69 Specification for Rolled Zinc B86 Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings B240 Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings B327 Specification for Master Alloys Used in Making Zinc Die Casting Alloys B418 Specification for Cast and Wrought Galvanic Zinc Anodes B750 Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings B792 Specification for Zinc Alloys in Ingot Form for Slush Casting B793 Specification for Zinc Casting Alloy Ingot for Sheet Metal Forming Dies and Plastic Injection Molds B833 Specification for Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) for the Corrosion Protection of Steel B852 Specification for Continuous Galvanizing Grade (CGG) Zinc Alloys for Hot-Dip Galvanizing of Sheet Steel B860 Specification for Zinc Master Alloys for Use in Hot Dip Galvanizing B892 Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy in Ingot Form for Die Castings B894 Specification for ACuZinc5 (Zinc-Copper-Aluminum) Alloy Die Castings B897 Specification for Configuration of Zinc and Zinc Alloy Jumbo Block and Half Block Ingot B899 Terminology Relating to Non-ferrous Metals and Alloys B907 Specification for Zinc, Tin and Cadmium Base Alloys Used as Solders B908 Practice for the Use of Color Codes for Zinc Casting Alloy Ingot B914 Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel

Additional information

Standard Title	B949-08 Standard Specification for General Requirements for Zinc and Zinc Alloy Products (Redline)
Published Code	ASTM
Publication Date	2008
Pages Count	6

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-B949 2008(Redline)

Related products