ASTM-D1037:2012 Edition

$58.50

D1037-12 Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials

Published By	Publication Date	Number of Pages
ASTM	2012	30

Guaranteed Safe Checkout

Category: ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM D1037-12

Historical Standard: Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials

ASTM D1037

Scope

1.1 Part AGeneral Test Methods for Evaluating the Basic Properties of Wood-Base Fiber and Particle Panel Materials. These test methods cover the determination of the properties of wood-base fiber and particle panel materials that are produced as mat-formed panels such as particleboard, medium-density fiberboard, hardboard, and oriented strand board.

1.2 Part BAcceptance and Specification Test Methods for Hardboard. The methods for Part B provide test procedures for measuring the following properties of hardboard:

1.3 There are accepted basic test procedures for various fundamental properties of materials that may be used without modification for evaluating certain properties of wood-based fiber and particle panel materials. These test methods are included elsewhere in the Annual Book of ASTM Standards. The pertinent ones are listed in Table 1. A few of the test methods referenced are for construction where the wood-base materials often are used.

1.4 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents are approximate in many cases. 1 in. = 25.4 mm, 1 lbf = 4.45 N.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

TABLE 1 Basic Test Procedures for Evaluating Properties of Wood Base-Fiber and Particle Panel Materials

^A Annual Book of ASTM Standards, Vol 04.06.

^B Annual Book of ASTM Standards, Vol 10.01.

^C Annual Book of ASTM Standards, Vol 04.10.

^D Annual Book of ASTM Standards, Vol 04.07.

^E Annual Book of ASTM Standards, Vol 14.02.

Keywords

hardboard; medium density fiberboard; oriented strand board; panels; particleboard; particle panel materials; wood; wood-base fiber; wood-base panel

ICS Code

ICS Number Code 79.040 (Wood, sawlogs and sawn timber)

DOI: 10.1520/D1037-12

PDF Catalog

PDF Pages	PDF Title
1	Scope
2	Referenced Documents Significance and Use Apparatus TABLE 1
3	Test Specimens Moisture Content and Conditioning Requirements Accelerated Aging
4	FIG. 1
5	Size, Physical Properties and Appearance of Panels FIG. 2 FIG. 3
6	Static Bending FIG. 4
7	FIG. 5
8	Tension Parallel to Surface FIG. 6 FIG. 7
9	Tension Perpendicular to Surface (Internal Bond) Compression Parallel to Surface
10	FIG. 8 FIG. 9
11	Lateral Nail Resistance FIG. 10
12	Nail Withdrawal Nail-Head Pull-Through FIG. 11
13	FIG. 12 FIG. 13 FIG. 14
14	Direct Screw Withdrawal Hardness
15	Hardness Modulus Shear in the Plane of the Panel FIG. 15
16	FIG. 16
17	FIG. 17
18	Glue-Line Shear (Block Type) FIG. 18 FIG. 19
19	Falling Ball Impact FIG. 20 FIG. 21
20	Abrasion Resistance by the U.S. Navy Wear Tester Water Absorption and Thickness Swelling FIG. 22 FIG. 23
21	Linear Expansion with Change in Moisture Content
22	Cupping and Twisting Interlaminar Shear FIG. 24
23	FIG. 25 FIG. 26 FIG. 27
24	Edgewise Shear FIG. 28
25	Compression-Shear FIG. 29 FIG. 30
26	FIG. 31
27	FIG. 32 TABLE 2
28	Test Panel Test Specimens Conditioning Thickness Modulus of Rupture FIG. 33
29	Tension Parallel to Surface Tension Perpendicular to Surface FIG. 34
30	Water Absorption and Thickness Swelling Moisture Content and Specific Gravity Report Precision and Bias Keywords

Additional information

Direct Screw Withdrawal	16
Thickness	32
Significance and Use	3
C177	Steady-State Heat-Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate ApparatusA
Static Bending	9
Falling Ball Impact	21
E906	Heat and Visible Smoke Release Rates for Materials and Prod- uctsD
Cupping and Twisting	25
Tension Strength Parallel to Surface	34
D1666	Conducting Machining Tests of Wood and Wood-Base MaterialsC
Compression Parallel to Surface	12
C423	Sound Absorption and Sound Absorption Coefficients by the Re- verberation Room MethodA
C384	Impedance and Absorption of Acoustical Materials by the Imped- ance Tube MethodA
Tension Perpendicular to Surface	11
E136	Behavior of Materials in a Vertical Tube Furnace at 750°CD
Fastener Holding Tests:
Lateral Nail Resistance	13
D150	A-C Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulating MaterialsB
Test Specimens	5
Edgewise Shear	27
E72	Conducting Strength Tests of Panels for Building ConstructionD
Water Absorption and Thickness Swelling	36
E162	Surface Flammability of Materials Using a Radiant Heat Energy SourceD
C236	Steady-State Thermal Performance of Building Assemblies by Means of the Guarded Hot BoxA
D1761	Mechanical Fasteners in WoodC
Moisture Content and Specific Gravity	37
E662	Specific Optical Density of Smoke Generated by Solid MaterialsD
D149	Dielectric Breakdown Voltage and Dielectric Strength of Solid Elec- trical Insulating Materials at Commercial Power FrequenciesB
E661	Performance of Wood and Wood-Based Floor and Roof Sheathing Under Concentrated Static and Impact LoadsD
Abrasion Resistance by the U.S. Navy Wear Tester	22
E84	Surface Burning Characteristics of Building MaterialsD
Moisture Content and Conditioning Requirements	6
Compression-Shear	28
C209	Cellulosic Fiber Insulating BoardA
E152	Fire Tests of Door AssembliesD
Glue-Line Shear (Block Type)	20
Nail-Head Pull-Through	15
D257	D-C Resistance or Conductance of Insulating MaterialsB
D495	High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical InsulationB
E119	Fire Tests of Building Construction and MaterialsD
Accelerated Aging	7
E90	Laboratory Measurement of Airborne Sound Transmission Loss of Building PartitionsA
Apparatus	4
Moisture Tests:
E97	Directional Reflectance Factor, 45-deg 0-deg, of Opaque Specimens by Broad-Band Filter ReflectometryE
E96	Water Vapor Transmission of MaterialsA
Size, Physical Properties and Appearance of Panels	8
Linear Expansion with Change in Moisture Content	24
Interlaminar Shear	26
Nail Withdrawal	14
Modulus of Rupture	33
Tension Strength Perpendicular to Surface	35
Tension Parallel to Surface	10
Shear in the Plane of the Panel	19
Hardness	17
Hardness Modulus	18