ASTM-D5055 2012(Redline)

$38.35

D5055-12 Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists (Redline)

Published By	Publication Date	Number of Pages
ASTM	2012	43

Guaranteed Safe Checkout

Category: ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

Abstract

This specification gives procedures for establishing, monitoring, and reevaluating structural capacities of prefabricated wood I-joists. Capacities considered are shear, moment, and stiffness. Procedures for establishing common details are given and certain design considerations specific to wood I-joists are itemized. Qualification is required for certain common details of I-joist application since they often influence structural capacities. All capacities are to be reported with three significant digits. Shear capacity qualification, moment capacity qualification, end joint qualification, stiffness capacity and creep qualification, and details of end use shall be established to meet the requirements prescribed. Design values are determined from the analysis and capacities as specified. The bearing capacity and regarded solid sawn lumber flanges shall be reevaluated to meet the requirements prescribed. The shear and flange material, and empirical moment capacity shall be tested to meet the requirements prescribed.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 General??? This specification gives procedures for establishing, monitoring, and reevaluating structural capacities of prefabricated wood I-joists. Capacities considered are shear, reaction, moment, and stiffness. Procedures for establishing common details are given and certain design considerations specific to wood I-joists are itemized.

1.2 Contents of the Standard??? An index and brief description of the main features of this specification are given in X1.1.1 .

1.3 Development of the Standard??? The development and intent of this specification is discussed in Appendix X1 .

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in 6.1.1.5 .

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D198 Test Methods of Static Tests of Lumber in Structural Sizes D245 Practice for Establishing Structural Grades and Related Allowable Properties for Visually Graded Lumber D1990 Practice for Establishing Allowable Properties for Visually-Graded Dimension Lumber from In-Grade Tests of Full-Size Specimens D2559 Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions D2915 Practice for Sampling and Data-Analysis for Structural Wood and Wood-Based Products D4761 Test Methods for Mechanical Properties of Lumber and Wood-Base Structural Material D5456 Specification for Evaluation of Structural Composite Lumber Products D5457 Specification for Computing Reference Resistance of Wood-Based Materials and Structural Connections for Load and Resistance Factor Design D7247 Test Method for Evaluating the Shear Strength of Adhesive Bonds in Laminated Wood Products at Elevated Temperatures D7480 Guide for Evaluating the Attributes of a Forest Management Plan E4 Practices for Force Verification of Testing Machines E529 Guide for Conducting Flexural Tests on Beams and Girders for Building Construction E699 Practice for Evaluation of Agencies Involved in Testing, Quality Assurance, and Evaluating of Building Components IEEE/ASTMÃ¢Â€Â‰SIÃ¢Â Standard for Use of the International System of Units (SI): The Modern Metric System

U.S. Product Standards

PS-20 American Softwood Lumber Standard

Keywords

ICS Code

ICS Number Code 79.080 (Semi-manufactures of timber)

DOI: 10.1520/D5055-12 ASTM International is a member of CrossRef.

ASTM D5055 (Wood Standards)

Citing ASTM Standards

[Back to Top]

Additional information

Standard Title	D5055-12 Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists (Redline)
Published Code	ASTM
Publication Date	2012
Pages Count	43

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-D5055 2012(Redline)

ASTM D5055 (Wood Standards)

Related products