Shopping Cart

No products in the cart.

ASTM-E1591:2007 Edition(Redline)

$30.55

E1591-07 Standard Guide for Obtaining Data for Deterministic Fire Models (Redline)

Published By Publication Date Number of Pages
ASTM 2007 16
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Significance and Use

This guide is intended primarily for users and developers of mathematical fire models. It is also useful for people conducting fire tests, making them aware of some important applications and uses for small-scale fire test results. The guide thus contributes to increased accuracy in fire model calculations, which depend greatly on the quality of the input data.

The emphasis of this guide is on zone models of compartment fires. However, other types of mathematical fire models need many of the same input variables.

Note 1—Mathematical fire models in this guide are referred to by their acronyms (see 5.4 ).

1. Scope

1.1 This guide describes data required as input for mathematical fire models.

1.2 Guidelines are presented on how the data can be obtained.

1.3 The emphasis in this guide is on compartment zone fire models.

1.4 The values stated in SI units are to be regarded as the standard.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.5 This fire standard cannot be used to provide quantitative measures.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

C177 Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus C518 Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus D835 Specification for Refined Benzene-485 D2395 Test Methods for Specific Gravity of Wood and Wood-Based Materials D3417 Test Method for Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry (DSC) D5865 Test Method for Gross Calorific Value of Coal and Coke E176 Terminology of Fire Standards E408 Test Methods for Total Normal Emittance of Surfaces Using Inspection-Meter Techniques E472 Practice for Reporting Thermoanalytical Data E537 Test Method for The Thermal Stability of Chemicals by Differential Scanning Calorimetry E793 Test Method for Enthalpies of Fusion and Crystallization by Differential Scanning Calorimetry E906 Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method E967 Test Method for Temperature Calibration of Differential Scanning Calorimeters and Differential Thermal Analyzers E968 Practice for Heat Flow Calibration of Differential Scanning Calorimeters E1321 Test Method for Determining Material Ignition and Flame Spread Properties E1354 Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter E1623 Test Method for Determination of Fire and Thermal Parameters of Materials, Products, and Systems Using an Intermediate Scale Calorimeter (ICAL) E2058 Test Methods for Measurement of Synthetic Polymer Material Flammability Using a Fire Propagation Apparatus (FPA) E2257 Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies

Keywords

air/fuel ratio; combustion efficiency; convective heat transfer coefficient; data for fire models; density; emissivity; entrainment coefficient; fire model; flame extinction coefficient; flame spread parameter; heat of combustion; heat of gasification; heat of pyrolysis; rate of heat release; ignition temperature; mass loss rate; material properties; production rate of species; pyrolysis temperature; specific heat; thermal conductivity; and thermal inertia;

ICS Code

ICS Number Code 13.220.01 (General standards related to fire protection)

DOI: 10.1520/E1591-07 ASTM International is a member of CrossRef.

ASTM-E1591
$30.55