ASTM-E662 2012(Redline)

$38.35

E662-12a Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials (Redline)

Published By	Publication Date	Number of Pages
ASTM	2012	28

Guaranteed Safe Checkout

Categories: 13.220.40 - Ignitability and burning behaviour of materials and products, 17.180.99 - Other standards related to optics and optical measurements, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

Significance and Use

5. Significance and Use Top Bottom

5.1 This test method provides a means for determining the specific optical density of the smoke generated by specimens of materials and assemblies under the specified exposure conditions. Values determined by this test are specific to the specimen or assembly in the form and thickness tested and are not to be considered inherent fundamental properties of the material tested. Thus, it is likely that closely repeatable or reproducible experimental results are not to be expected from tests of a given material when specimen thickness, density, or other variables are involved.

5.2 The photometric scale used to measure smoke by this test method is similar to the optical density scale for human vision. However, physiological aspects associated with vision are not measured by this test method. Correlation with measurements by other test methods has not been established. ⁴

5.3 At the present time no basis is provided for predicting the density of smoke generated by the materials upon exposure to heat and flame under other fire conditions.

5.4 The test method is of a complex nature and the data obtained are sensitive to variations which in other test methods might be considered to be insignificant (see Section 6 ). A precision statement based on the results of a roundrobin test by a prior draft version of this test method is given in 14.1

5.5 In this procedure, the specimens are subjected to one or more specific sets of laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test method to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire test exposure conditions described in this procedure.

1. Scope

1.1 This fire-test-response standard covers determination of the specific optical density of smoke generated by solid materials and assemblies mounted in the vertical position in thicknesses up to and including 1 in. (25.4 mm).

1.2 Measurement is made of the attenuation of a light beam by smoke (suspended solid or liquid particles) accumulating within a closed chamber due to nonflaming pyrolytic decomposition and flaming combustion.

1.3 Results are expressed in terms of specific optical density which is derived from a geometrical factor and the measured optical density, a measurement characteristic of the concentration of smoke.

1.4 This test method is intended for use in research and development and not as a basis for ratings for regulatory purposes.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D2843 Test Method for Density of Smoke from the Burning or Decomposition of Plastics E176 Terminology of Fire Standards

Keywords

fire; fire-test response standard; smoke; smoke chamber; smoke density; smoke obscuration; solids; specific optical density ;

ICS Code

ICS Number Code 13.220.40 (Ignitability and burning behaviour of materials and products); 17.180.99 (Other standards related to optics and optical measurements)

DOI: 10.1520/E0662-12A ASTM International is a member of CrossRef.

ASTM E662 (Fire Standards and Flammability Standards)

Citing ASTM Standards

Additional information

Standard Title	E662-12a Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials (Redline)
Published Code	ASTM
Publication Date	2012
Pages Count	28
ICS Codes	13.220.40 - Ignitability and burning behaviour of materials and products 17.180.99 - Other standards related to optics and optical measurements

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-E662 2012(Redline)

ASTM E662 (Fire Standards and Flammability Standards)

Related products