🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
AWWA C216 2022

AWWA C216 2022

$76.92

AWWA C216-22 Heat-Shrinkable Cross-Linked Polyolefin Coatings for Steel Water Pipe and Fittings

Published By Publication Date Number of Pages
AWWA 2022 28
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

The purpose of this standard is to provide the minimum requirements for heat-shrinkable coatings, including material, application, inspection, testing, marking, and packaging.

PDF Catalog

PDF Pages PDF Title
9 Foreword
I. Introduction.
I.A. Background. Heat-shrinkable cross-linked polyolefin coatings for external use on special sections, connections, and fittings for underground steel water pipelines have been used since 1960. This standard establishes required performance standards for
I.B. History. The first edition of this standard was approved by the AWWA Board of Directors on Jan. 29, 1989, and had an effective date of July 1, 1989. Subsequent editions were approved on June 19, 1994, with an effective date of Aug. 1, 1995; on Jan. 2
II. Special Issues.
II.A. General. ANSI/AWWA C216 is intended to govern the exterior coating of special sections, connections, and fittings for underground steel water pipelines. These types of coatings are generally used on pipe that has been coated before transportation to
II.B. Weld-After-Backfill. Weld-after-backfill is the sequence of assembling a welded joint, tack welding the outside joint, applying the exterior joint coating(s), backfilling the pipe joint, and then welding the inside joint at a later time (where inter
10 III. Use of This Standard. It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the particular application being considered.
III.A. Purchaser Options and Alternatives. The following items should be included by the purchaser:
11 IV. Major Revisions. Major changes made to the standard in this edition are as follows:
V. Comments. If you have any comments or questions about this standard, please call AWWA Engineering and Technical Services at 303.794.7711; FAX at 303.795.7603; write to the department at 6666 West Quincy Avenue, Denver, CO 80235-3098; or email at standa
13 AWWA Standard
SECTION 1: GENERAL
Sec. 1.1 Scope
14 Sec. 1.2 Purpose
Sec. 1.3 Application
SECTION 2: REFERENCES
15 SECTION 3: DEFINITIONS
16 SECTION 4: REQUIREMENTS
Sec. 4.1 Equipment
Sec. 4.2 Materials and Workmanship
Sec. 4.3 Coating System
17 Sec. 4.4 Surface Preparation
18 Sec. 4.5 Coating Application (Field and Shop)
19 Sec. 4.6 Coating Repair
Sec. 4.7 Field Procedures
20 SECTION 5: VERIFICATION
Sec. 5.1 Coating Materials Prequalification
Sec. 5.2 Prequalification Requirements of Coating System
22 Table 1 Prequalification requirements of coating system
Sec. 5.3 Quality Assurance and Records
Sec. 5.4 Inspection and Testing by the Purchaser
23 Sec. 5.5 Quality Control Requirements of Applied Coating System
26 Sec. 5.6 Rejection
SECTION 6: DELIVERY
Sec. 6.1 Marking
Sec. 6.2 Packaging and Shipping
27 Sec. 6.3 Affidavit of Compliance

Related products

AWWA C216 2022
$76.92