BS EN 13160-2:2016
$198.66
Leak detection systems – Requirements and test/assessment methods for pressure and vacuum systems
| Published By | Publication Date | Number of Pages |
| BSI | 2016 | 70 |
This European Standard gives requirements and the corresponding test/assessment methods applicable to leak detection kits (leak detector) based on the measurement of pressure change. Leak detection kits are intended to be used with double skin, underground or above ground, pressurized or non-pressurized, tanks or pipework designed for water polluting liquids/fluids. The kits are usually composed of: – measuring device; – evaluation device; – alarm device; – pressure generator; – pressure relief device; – liquid stop device; – condensate trap.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 4 | Contents Page |
| 8 | 1 Scope 2 Normative references |
| 9 | 3 Terms, definitions, symbols and abbreviated terms 3.1 Terms and definitions 3.2 Symbols and abbreviated terms |
| 11 | 4 Requirements 4.1 Effectiveness 4.1.1 General 4.1.2 Measure the pressure change 4.1.2.1 Measuring device for over pressure 4.1.2.2 Evaluation device for over pressure |
| 12 | 4.1.2.3 Alarm device for over pressure 4.1.2.4 Measuring device for vacuum 4.1.2.5 Evaluation device for vacuum |
| 14 | 4.1.2.6 Alarm device for vacuum 4.1.3 Replenishment rate of the medium (only if provided) 4.1.3.1 Vacuum and pressure generators with regulated flow rate 4.1.3.2 Pressure / vacuum generator with time regulated flow |
| 15 | 4.1.4 Software (only if provided) 4.1.5 Function and tightness of leak detection kit 4.2 Durability of effectiveness 4.2.1 Durability of effectiveness against temperature 4.2.2 Durability of effectiveness against chemical attack 4.2.3 Durability of effectiveness against fatigue through cycling of pressure 4.2.4 Humidity measurement of the leak detection medium (only if provided) |
| 16 | 4.3 Additional requirement 4.3.1 Over pressure change 4.3.2 Vacuum change 4.3.2.1 Liquid stop device 4.3.2.2 Condensate trap |
| 17 | 5 Testing, assessment and sampling methods 5.1 Effectiveness 5.1.1 General 5.1.2 Measure the pressure change 5.1.2.1 Measuring device for over pressure |
| 19 | 5.1.2.2 Evaluation device for over pressure |
| 21 | 5.1.2.3 Alarm device for over pressure |
| 22 | 5.1.2.4 Measuring device for vacuum |
| 23 | 5.1.2.5 Evaluation device for vacuum |
| 25 | 5.1.2.6 Alarm device for vacuum 5.1.3 Replenishment rate of the medium (only if provided) 5.1.3.1 Vacuum and pressure generators with regulated flow rate |
| 26 | 5.1.3.2 Pressure/vacuum generator with time regulated flow |
| 30 | 5.1.4 Software (only if provided) 5.1.4.1 Test equipment 5.1.4.2 Preparation 5.1.4.3 Procedure 5.1.4.4 Evaluation |
| 31 | 5.1.5 Function and tightness of leak detection kits 5.1.5.1 Test equipment 5.1.5.2 Preparation 5.1.5.3 Procedure 5.1.5.4 Evaluation |
| 32 | 5.2 Durability of effectiveness 5.2.1 Durability of effectiveness against temperature 5.2.1.1 Test equipment 5.2.1.2 Preparation |
| 33 | 5.2.1.3 Procedure |
| 34 | 5.2.1.4 Evaluation |
| 35 | 5.2.2 Durability of effectiveness against chemical attack 5.2.2.1 Test equipment 5.2.2.2 Preparation 5.2.2.3 Procedure |
| 36 | 5.2.2.4 Evaluation 5.2.3 Durability of effectiveness against fatigue through cycling of pressure 5.2.3.1 Test equipment 5.2.3.2 Preparation 5.2.3.3 Procedure 5.2.3.4 Evaluation |
| 37 | 5.2.4 Humidity measurement of the leak detection medium (only if provided) 5.2.4.1 Test equipment 5.2.4.2 Preparation 5.2.4.3 Procedure 5.2.4.4 Evaluation 5.3 Additional tests 5.3.1 Device for over pressure 5.3.1.1 Pressure relief valve |
| 38 | 5.3.2 Device for vacuum 5.3.2.1 Liquid stop device |
| 40 | 5.3.2.2 Condensate trap |
| 41 | 6 Assessment and verification of constancy of performance – AVCP 6.1 General 6.2 Type testing 6.2.1 General |
| 42 | 6.2.2 Test samples, testing and compliance criteria 6.2.3 Test reports 6.2.4 Shared other party results |
| 43 | 6.2.5 Cascading determination of the product type results |
| 44 | 6.3 Factory production control (FPC) 6.3.1 General |
| 45 | 6.3.2 Requirements 6.3.2.1 General |
| 46 | 6.3.2.2 Equipment 6.3.2.3 Raw materials and components 6.3.2.4 Traceability and marking 6.3.2.5 Controls during manufacturing process 6.3.2.6 Product testing and evaluation 6.3.2.7 Non-complying products |
| 47 | 6.3.2.8 Corrective action 6.3.2.9 Handling, storage and packaging 6.3.3 Product specific requirements |
| 48 | 6.3.4 Procedure for modifications 6.3.5 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity |
| 49 | 7 Marking, labelling and packaging 8 Environmental aspects |
| 50 | Annex A (normative) Calculation of the dry filter A.1 Flow rate of air in the dry filter A.1.1 Influences of temperature A.1.2 Calculated loss of volume (due to influences to temperature) |
| 51 | A.1.3 Influence by leakage A.1.4 Summarization A.1.5 Calculation of the contents of the dry filter |
| 52 | Annex B (normative)Test of the over pressure device B.1 Test equipment B.2 Preparation |
| 53 | B.3 Procedure B.3.1 Parametric test method B.3.2 Test program |
| 54 | B.4 Evaluation |
| 55 | Annex C (informative)Environmental aspects |
| 58 | Annex ZA (informative)Clauses of this European Standard addressing the provisions of the EU Directive Construction Products Regulation 305/2011/EU |
Related products
-
BS EN 13160-2:2016 – TC:2020 Edition
Tracked Changes. Leak detection systems – Requirements and test/assessment methods for pressure and vacuum systems…
