🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 1366-4:2021

BS EN 1366-4:2021

$198.66

Fire resistance tests for service installations – Linear joint seals

Published By Publication Date Number of Pages
BSI 2021 64
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This part of the EN 1366 series specifies a method for determining the fire resistance of linear joint seals based on their intended end use. Perimeter seals of curtain walling are excluded from this part of the EN 1366 series.

This document is intended to be used in conjunction with EN 1363?1.

The following tests are included in this document:

  1. no mechanically induced movement;

  2. mechanically induced movement.

Tests in accordance with this part of the EN 1366 series are not intended to provide quantitative information on the rate of leakage of smoke and/or hot gases, or on the transmission or generation of fumes. Such phenomena are only noted in the test report in describing the general behaviour of test specimens during the test.

The load-bearing capacity of a linear joint seal is not addressed in this part of the EN 1366 series. No information can be implied by the test concerning the influence of the inclusion of linear joint seals on the loadbearing capacity of the separating element.

PDF Catalog

PDF Pages PDF Title
2 undefined
undefined
9 1 Scope
1 Scope
2 Normative references
2 Normative references
3 Terms and definitions
3 Terms and definitions
10 4 Test equipment
4 Test equipment
11 5 Test conditions
5 Test conditions
5.1 Heating conditions
5.1 Heating conditions
5.2 Pressure conditions
5.2 Pressure conditions
6 Test specimen
6 Test specimen
6.1 General
6.1 General
6.2 Size
6.2 Size
6.3 Number of test specimens
6.3 Number of test specimens
12 7 Installation of test specimen
7 Installation of test specimen
7.1 General
7.1 General
7.2 Requirements for specific seal types
7.2 Requirements for specific seal types
7.2.1 Seals made of fabrics
7.2.1 Seals made of fabrics
7.2.2 Seals made of foams (foamed in situ)
7.2.2 Seals made of foams (foamed in situ)
13 7.2.3 Membrane forming seals
7.2.3 Membrane forming seals
7.2.4 Seals made of mineral wool (faced/coated or not faced/coated)
7.2.4 Seals made of mineral wool (faced/coated or not faced/coated)
14 7.2.5 Linear joint seal made of mortar/plaster
7.2.5 Linear joint seal made of mortar/plaster
15 7.2.6 Linear joint seal made of sealants
7.2.6 Linear joint seal made of sealants
7.2.7 Linear joint seal made of pre-formed compressible strips
7.2.7 Linear joint seal made of pre-formed compressible strips
16 7.2.8 Linear joint seals made of pre-formed compressible composite strips
7.2.8 Linear joint seals made of pre-formed compressible composite strips
17 7.2.9 Linear joint seal made of pre-formed compressible ropes
7.2.9 Linear joint seal made of pre-formed compressible ropes
7.2.10 Linear joint seal made of pre-formed strips
7.2.10 Linear joint seal made of pre-formed strips
18 7.3 Supporting construction
7.3 Supporting construction
7.3.1 General
7.3.1 General
20 7.3.2 Standard supporting construction
7.3.2 Standard supporting construction
7.3.2.1 Wall constructions
7.3.2.1 Wall constructions
7.3.2.2 Floor constructions
7.3.2.2 Floor constructions
21 7.3.2.3 Steel joint faces
7.3.2.3 Steel joint faces
23 7.4 Test construction
7.4 Test construction
26 7.5 Splice locations
7.5 Splice locations
7.6 Induced movement
7.6 Induced movement
8 Conditioning
8 Conditioning
9 Application of instrumentation
9 Application of instrumentation
9.1 General
9.1 General
9.2 Thermocouples
9.2 Thermocouples
9.2.1 Furnace thermocouples
9.2.1 Furnace thermocouples
9.2.2 Unexposed face thermocouples
9.2.2 Unexposed face thermocouples
38 9.3 Roving thermocouple
9.3 Roving thermocouple
9.4 Deformation and deflection
9.4 Deformation and deflection
39 9.5 Integrity measurement
9.5 Integrity measurement
10 Test procedure
10 Test procedure
10.1 General
10.1 General
10.2 Installation of test construction
10.2 Installation of test construction
10.3 Mechanically induced movement of the test specimen
10.3 Mechanically induced movement of the test specimen
10.4 Measurements and observations
10.4 Measurements and observations
11 Performance criteria
11 Performance criteria
11.1 Insulation
11.1 Insulation
11.2 Integrity
11.2 Integrity
40 11.3 Expression of results
11.3 Expression of results
12 Test report
12 Test report
13 Field of direct application of test results
13 Field of direct application of test results
13.1 Orientation
13.1 Orientation
41 13.2 Supporting construction
13.2 Supporting construction
13.2.1 Rigid constructions
13.2.1 Rigid constructions
43 13.2.2 Flexible wall constructions
13.2.2 Flexible wall constructions
13.2.3 Flexible floor constructions
13.2.3 Flexible floor constructions
13.2.4 Non-standard supporting constructions
13.2.4 Non-standard supporting constructions
13.3 Seal position
13.3 Seal position
13.4 Mechanically induced movement
13.4 Mechanically induced movement
44 13.5 Dimensions
13.5 Dimensions
13.5.1 Linear joint seal made of fabrics
13.5.1 Linear joint seal made of fabrics
13.5.2 Linear joint seal made of foams – foamed in situ
13.5.2 Linear joint seal made of foams – foamed in situ
13.5.3 Membrane forming seals
13.5.3 Membrane forming seals
13.5.4 Linear joint seal made of mineral wool (faced/coated or not faced/coated)
13.5.4 Linear joint seal made of mineral wool (faced/coated or not faced/coated)
13.5.5 Linear joint seal made of mortar/plaster
13.5.5 Linear joint seal made of mortar/plaster
13.5.6 Linear joint seal made of sealants
13.5.6 Linear joint seal made of sealants
45 13.5.7 Linear joint seal made of pre-formed compressible strips
13.5.7 Linear joint seal made of pre-formed compressible strips
46 13.5.8 Linear joint seals made of pre-formed compressible composite strips
13.5.8 Linear joint seals made of pre-formed compressible composite strips
13.5.9 Linear joint seal made of pre-formed compressible ropes
13.5.9 Linear joint seal made of pre-formed compressible ropes
47 13.5.10 Linear joint seal made of pre-formed strips
13.5.10 Linear joint seal made of pre-formed strips
48 Annex A (normative)Standard condition for linear joint seals with no mechanically induced movement of the joint faces
Annex A (normative)Standard condition for linear joint seals with no mechanically induced movement of the joint faces
A.1 Standard condition
A.1 Standard condition
A.2 Test procedure
A.2 Test procedure
49 Annex B (normative)Standard condition for linear joint seals with mechanically induced movement of the joint faces
Annex B (normative)Standard condition for linear joint seals with mechanically induced movement of the joint faces
B.1 General
B.1 General
B.2 Standard condition(s)
B.2 Standard condition(s)
B.2.1 Standard condition for lateral movement
B.2.1 Standard condition for lateral movement
51 B.2.2 Standard condition for shear movement
B.2.2 Standard condition for shear movement
52 B.2.3 Standard condition for a combination of lateral and shear movement
B.2.3 Standard condition for a combination of lateral and shear movement
54 Annex C (informative)Guidance on the use of this document
Annex C (informative)Guidance on the use of this document
C.1 General
C.1 General
C.2 Application of the test
C.2 Application of the test
C.3 Test conditions
C.3 Test conditions
55 C.4 Specimen preparation
C.4 Specimen preparation
C.5 Notes on general performance criteria
C.5 Notes on general performance criteria
C.6 Notes on validity of test results
C.6 Notes on validity of test results
56 C.7 Notes on Annex B
C.7 Notes on Annex B

Related products

BS EN 1366-4:2021
$198.66