BS EN 13830:2015+A1:2020
$215.11
Curtain walling. Product standard
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 94 |
This European Standard specifies requirements of curtain walling kit intended to be used as a building envelope to provide weather resistance, safety in use and energy economy and heat retention and provides test/assessments/calculation methods and compliance criteria of the related performances. The curtain walling kit covered by this standard should fulfil its own integrity and mechanical stability but does not contribute to the load bearing or stability of the main building structure, and could be replaced independently of it. This standard applies to curtain walling kit ranging from a vertical position to ± 15° from the vertical. Any sloping parts should be contained within the curtain walling kit. This standard is applicable to the whole of the curtain walling kits, including the fixings. Curtain walling according to this standard is intended to be used as part of the building envelope. This European Standard does not include: – Patent glazing (glazed sloping roofs) kits; – Roof glazing constructions; – Façades made of precast concrete panels as part of the wall (see EN 14992). NOTE 1 Precast concrete panels may be used in curtain walling kits as infill panels. NOTE 2 Durability of structural sealed glazing infills is not covered by this standard.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | undefined |
| 10 | 1 Scope 2 Normative references |
| 14 | 3 Terms, definitions and abbreviated terms 3.1 Definitions |
| 16 | 3.2 Abbreviations used in this standard 4 Product characteristics 4.1 Reaction to fire (of components, when relevant) |
| 17 | 4.2 Fire resistance 4.3 Fire propagation (to upper levels) 4.4 Watertightness 4.5 Resistance to its own dead load 4.6 Wind load resistance |
| 18 | 4.7 Resistance to snow load (only for elements subjected to snow load) 4.8 Impact resistance 4.8.1 General 4.8.2 Internal 4.8.3 External 4.9 Resistance to live horizontal loads at sill level 4.10 Seismic resistance 4.10.1 General |
| 19 | 4.10.2 Safety in use 4.10.3 Serviceability (where specially required) 4.11 Thermal shock resistance 4.12 Direct airborne sound insulation 4.13 Flanking sound transmission 4.14 Thermal transmittance 4.15 Air permeability 4.16 Water vapour permeability |
| 20 | 4.17 Radiation properties 4.18 Durability 4.18.1 General 4.18.2 Durability of watertightness 4.18.3 Durability of thermal transmittance 4.18.4 Durability of air permeability |
| 21 | 5 Testing, assessment and sampling methods 5.1 Sampling 5.1.1 General 5.1.2 Sequence of testing |
| 22 | 5.2 Reaction to fire (of components, when relevant) 5.3 Fire resistance 5.4 Fire propagation (to upper levels) 5.5 Watertightness 5.6 Resistance to its own dead load |
| 23 | 5.7 Wind load resistance 5.8 Resistance to snow load (only for elements subject to snow load) 5.9 Impact resistance |
| 24 | 5.10 Resistance to live horizontal loads at sill level 5.11 Seismic resistance 5.11.1 Safety in use 5.11.2 Serviceability (where specially required) 5.12 Direct airborne sound insulation 5.13 Flanking sound transmission 5.14 Thermal transmittance |
| 25 | 5.15 Air permeability 5.16 Radiation properties 5.17 Durability 5.17.1 General 5.17.2 Durability of watertightness |
| 26 | 5.17.3 Durability of thermal transmittance 5.17.4 Durability of air permeability |
| 27 | 6 Assessment and verification of constancy of performance (AVCP) 6.1 General 6.2 Type testing 6.2.1 General |
| 28 | 6.2.2 Test samples, testing and compliance criteria |
| 29 | 6.2.3 Test reports 6.2.4 Cascading determination of the product type results |
| 30 | 6.3 Factory production control (FPC) 6.3.1 General |
| 31 | 6.3.2 Requirements 6.3.2.1 General |
| 32 | 6.3.2.2 Equipment 6.3.2.3 Raw materials and components 6.3.2.4 Traceability and marking 6.3.2.5 Controls during manufacturing process 6.3.2.6 Product testing and evaluation |
| 33 | 6.3.2.7 Non-complying products |
| 34 | 6.3.2.8 Corrective action 6.3.2.9 Handling, storage and packaging 6.3.3 Product specific requirements 6.3.4 Initial inspection of factory and of FPC |
| 35 | 6.3.5 Continuous surveillance of FPC (only for curtain walling kits covered by AVCP system 1) 6.3.6 Procedure for modifications 6.3.7 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity |
| 40 | Annex A “(informative)Resistance to actions: guidance on the use of Eurocodes A.1 Introduction of the annex A.2 Scope of the annex A.3 Symbols and abbreviations in the annex |
| 41 | A.4 Definition and principle A.4.1 General |
| 42 | A.4.2 Classes of consequence A.4.3 Curtain walling kit operating as safety barrier A.4.4 Loaded area “A” |
| 44 | A.4.5 System redundancy A.5 Requirements A.6 Actions A.6.1 Dead load action A.6.2 Wind action |
| 45 | A.6.3 Actions for curtain walling serving as parapets |
| 46 | A.7 Assumptions related the combinations of actions A.7.1 General |
| 47 | A.7.2 Combinations of actions: generalities |
| 52 | Annex B “(normative)Seismic resistance B.1 General principles B.1.1 Required performance limits B.1.2 Factors affecting seismic performance B.2 Assessment of seismic serviceability limit |
| 53 | B.3 Assessment of seismic safety limit B.4 Seismic movement regime B.4.1 General |
| 54 | B.4.2 Principles B.4.3 Test apparatus B.4.4 Test procedure |
| 60 | Annex C “(normative)Selection, preparation, mounting and fixing of test specimen for reaction to fire tests of curtain walling and field of direct application C.1 General |
| 61 | C.2 EN ISO 119252:2010 (Single flame test) C.2.1 Profile |
| 63 | C.2.2 Infill C.2.3 Sealing between infill and profile |
| 65 | C.2.4 Organic coating/top layers C.3 Mounting and fixing for EN 13238 (SBI-test) |
| 66 | C.4 EN ISO 1182 (Non-combustibility test) |
| 67 | C.5 EN ISO 1716 (Determination of the heat of combustion) C.6 Field of direct application |
| 69 | Annex D “(normative)Characteristics and range of direct application D.1 General |
| 76 | D.2 Selection of a representative test specimen |
| 79 | Annex E “(informative)Characteristics and performances of curtain walling kit |
| 82 | Annex F “(informative)Interchangeability between characteristics and components |
| 85 | Annex G “(informative)Basic approach to durability |
| 87 | Annex ZA (informative)!Relationship to this European Standard with Regulation (EU) No.305/2011(When applying this standard as a harmonized standard under Regulation (EU) No. 305/2011, manufacturers and Member States are obliged by this regulation to use this Annex) ” |
