BS EN 14303:2009+A1:2013
$167.15
Thermal insulation products for building equipment and industrialinstallations. Factory made mineral wool (MW) products. Specification
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 38 |
This European Standard specifies the requirements for factory made mineral wool products, which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately 0 °C to + 800 °C.
NOTE Below an operating temperature of ambient, special means against water vapour diffusion and water accumulation by air flow might be required. Below an operating temperature of – 50 °C, special tests regarding the suitability of the products in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer’s advice should be heeded in all cases.
The products are manufactured with or without facings or coatings, in the form of rolls, boards, slabs, mats, felts, quilts, wired mats, lamella mats, bevelled lags and pipe sections.
This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.
This European Standard does not specify the required level of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.
Products with a declared thermal conductivity greater than 0,065 W/(m·K) at 10 °C are not covered by this standard.
This Eurpean Standard does not cover products for in situ insulation (blowing or pouring) or products for the insulation of the building structure.
This European Standard does not cover the following acoustical aspects: direct airborne sound insulation and impact noise transmission index.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 7 | 1 Scope 2 Normative references |
| 8 | 3 Terms, definitions, symbols, units and abbreviated terms 3.1 Terms and definitions |
| 9 | 3.1.1 Terms and definitions as given in EN ISO 9229:2007 3.1.2 Additional terms and definitions |
| 10 | 3.2 Symbols, units and abbreviated terms 3.2.1 Symbols and units used in this standard |
| 11 | 3.2.2 Abbreviations used in this standard 4 Requirements 4.1 General |
| 12 | 4.2 For all applications 4.2.1 Thermal conductivity 4.2.2 Dimensions and tolerances 4.2.2.1 Linear dimensions |
| 13 | Table 1 — Levels and classes for thickness tolerances Table 2 — Levels and classes for dimensional tolerances |
| 14 | 4.2.2.2 Squareness 4.2.3 Dimensional stability 4.2.4 Reaction to fire of the product as placed on the market |
| 15 | 4.2.5 Durability characteristics 4.2.5.1 General 4.2.5.2 Durability of reaction to fire against ageing/degradation and high temperature 4.2.5.3 Durability of thermal resistance against ageing/degradation 4.2.5.4 Durability of thermal resistance against high temperature 4.3 For specific applications 4.3.1 General 4.3.2 Maximum service temperature exceed a deformation under the defined load by more than 5 %; 4.3.3 Minimum service temperature 4.3.4 Compressive stress or compressive strength |
| 16 | 4.3.5 Water absorption 4.3.6 Water vapour diffusion resistance Table 4 — Water vapour diffusion equivalent air layer thickness 4.3.7 Trace quantities of water soluble ions and the pH-value 4.3.8 Sound absorption |
| 17 | 4.3.9 Release of dangerous substances 4.3.10 Continuous glowing combustion 5 Test methods 5.1 Sampling 5.2 Conditioning 5.3 Testing 5.3.1 General 5.3.2 Thermal conductivity |
| 19 | Table 5 — Test methods, specimens and conditions Dimensions in millimetres |
| 20 | 5.3.3 Reaction to fire 6 Designation code |
| 21 | MW EN 14303–T2–ST(+)650–CS(10)20–WS1–MV1–CL6–pH9,5 7 Evaluation of conformity 7.1 General 7.2 Initial Type Test 7.3 Factory Production Control 8 Marking and labelling product name or other identifying characteristic; |
| 23 | Annex A (normative) Factory production control |
| 27 | Annex B (informative) Additional Properties B.1 General B.3 Flatness B.4 Airflow resistivity B.5 Dynamic stiffness |
| 29 | Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive ZA.1 Scope and relevant characteristics |
| 30 | Table ZA.1 — Relevant clauses |
| 31 | ZA.2 Procedures for attestation of conformity of factory made mineral wool products ZA.2.1 Systems of attestation of conformity Table ZA.2 — System(s) of attestation of conformity |
| 32 | Table ZA.3 — Assignment of evaluation of conformity tasks for products under system 1 |
| 33 | ZA.2.2 EC certificate and declaration of conformity |
| 35 | ZA.3 CE Marking and labelling |
