BS EN 15059:2009+A1:2015
$142.49
Snow grooming equipment. Safety requirements
| Published By | Publication Date | Number of Pages |
| BSI | 2015 | 30 |
This standard applies to snow grooming equipment as defined in 3.1 and its use with attachments as described in 3.2. With the exception of rear-mounted snow tillers and front blade attachments, this standard does not deal with the specific hazards of the attachments themselves. This standard is not applicable to snowmobiles.
This standard deals with all significant hazards, hazardous situations and events relevant to snow grooming equipment, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). It also deals with hazards during commissioning, use, fault-finding and maintenance.
This standard is not applicable to snow grooming equipment manufactured before the date of publication of this document by CEN.
For travelling on public roads, national traffic regulations apply until harmonised requirements are available.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Introduction |
| 8 | 1 Scope 2 Normative references |
| 9 | 3 Terms and definitions |
| 10 | Figure 1 — Snow grooming equipment with main components 4 List of significant hazards Table 1 — List of significant hazards |
| 11 | 5 Safety requirements and/or protective measures 5.1 General |
| 12 | 5.2 Steering system 5.3 Brakes 5.4 Setting in motion |
| 13 | 5.5 Tensioners for tracks 5.6 Driver’s cab 5.6.1 General” Table 2 — Test loads for snow grooming equipment |
| 14 | 5.6.2 Seat 5.6.2.1 General” |
| 15 | 5.6.2.2 Additional seats 5.7 Transport of persons outside the driver’s cab 5.8 Control systems and their actuators, instruments |
| 16 | 5.9 Measures to prevent effects dangerous to health 5.10 Lighting systems and recognisability Table 3 — Special warning lamp (beacon) |
| 17 | 5.11 Acoustic warning devices 5.12 Rear-view mirrors 5.13 Equipment holders 5.14 Working attachments |
| 18 | 5.15 Provision for maintenance 5.16 Noise 5.16.1 Noise reduction by design 5.16.1.1 Noise reduction at source 5.16.1.2 Noise reduction by protective measures |
| 19 | 5.16.1.3 Noise reduction by information 5.16.2 Measurement and declaration of noise emission 5.16.2.1 Determination of the emitted sound power level 5.16.2.2 Determination of the A-weighted emission sound pressure level at the operator’s position 5.16.2.3 Declaration and verification of noise emission values 6 Verification of safety requirements and/or protective measures 7 Information for use 7.1 Accompanying documents |
| 22 | 7.2 Machine marking |
| 23 | Annex A (normative) Data Table A.1 — Definition of input spectral class Table A.2 — Filter cut-off frequencies Table A.3 — Characteristics of the simulated input vibration |
| 24 | Annex B (normative) !Transport of persons outside the driver’s cab B.1 General requirements B.2 Additional requirements for the use of cabins for the transport of persons |
| 25 | B.3 Conditions to deviate from requirements of B.1 of roll-over protective structures |
| 26 | Figure B.1 — Tipping point” |
| 28 | Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC |
| 29 | Bibliography |
Related products
-
BS EN 17106-1:2021
Road operation machinery. Safety – General requirements Published By Publication Date Number of Pages BSI…
