šŸ”„šŸ”„ Donā€™t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

šŸ”
BS EN 1519-1:2019:2021 Edition

BS EN 1519-1:2019:2021 Edition

$167.15

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE) – Requirements for pipes, fittings and the system

Published By Publication Date Number of Pages
BSI 2021 42
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

This document specifies the requirements for solid-wall polyethylene (PE) pipes with smooth internal and external surfaces extruded from the same compound/formulation throughout the wall, fittings and the system for:

  • soil and waste discharge applications (low and high temperature) inside buildings (application area code ā€œBā€);

  • soil and waste discharge applications (low and high temperature) for both inside buildings and buried in the ground within the building structure (application area code ā€œBDā€).

NOTE 1 The intended use is reflected in the marking of products by ā€œBā€ or ā€œBDā€.

NOTE 2 For use buried in the ground within the building structure are intended only those components marked with ā€œBDā€, with a nominal ring stiffness of at least SN4 for dimensions equal to or greater than 75 mm.

This document is also applicable to PE pipes and fittings and the system intended for the following purposes:

  • ventilating part of the pipework in association with discharge applications;

  • rainwater pipework within the building structure.

It also specifies the test parameters for the test methods referred to in this standard.

This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.

NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes, e.g. CEN/TR 13801 [1].

NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, if applicable.

It applies to pipes and fittings, marked with ā€œBā€, which are intended to be used inside buildings and outside buildings fixed onto the wall.

It applies to pipes and fittings, marked with ā€œBDā€, which are intended to be used for both inside buildings and buried in the ground within the building structure.

This standard is applicable to PE pipes and fittings of the following types:

  • plain-ended;

  • with integral elastomeric ring seal socket;

  • for butt fusion joints;

  • for electrofusion joints;

  • for mechanical joints

where the fittings can be manufactured by injection-moulding or can be fabricated from pipes and/or mouldings.

NOTE 5 EN 476[2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements.

NOTE 6 For information about the chemical resistance of PE, guidance is given in ISO/TR 10358[3] and for rubber materials in ISO/TR 7620[4].

PDF Catalog

PDF Pages PDF Title
2 undefined
9 1 Scope
10 2 Normative references
11 3 Terms and definitions
14 4 Symbols and abbreviations
4.1 Symbols
4.2 Abbreviations
5 Material
5.1 PE compound
5.2 Additional requirement for pipe and fitting material for application area BD
15 5.3 Utilization of non-virgin material
5.4 Melt mass-flow rate
5.5 Fusion compatibility
5.6 Thermal stability (OIT)
5.7 Sealing ring retaining means
5.8 Fire behaviour
16 6 General characteristics
6.1 General
6.2 Colour
7 Geometrical characteristics
7.1 General
7.2 Dimensions of pipes
7.2.1 Outside diameters
17 7.2.2 Effective length of pipes
18 7.2.3 Chamfering
7.2.4 Wall thickness
20 7.3 Dimensions of fittings
7.3.1 Outside diameters
7.3.2 Design lengths
7.3.3 Wall thickness
21 7.4 Dimensions of sockets and pipe ends
7.4.1 Dimensions of ring seal sockets and spigot ends
7.4.1.1 Diameters and lengths
23 7.4.1.2 Wall thickness of ring seal sockets
25 7.4.2 Dimensions of electrofusion sockets
26 7.4.3 Dimensions of pipe ends for butt fusion joints
27 7.5 Types of fittings
32 8 Mechanical characteristics
8.1 Mechanical characteristics for pipes
8.2 Mechanical characteristics of fittings
33 9 Physical characteristics
9.1 Physical characteristics of pipes
34 9.2 Physical characteristics of fittings
10 Performance requirements
36 11 Sealing rings
12 Marking
12.1 General
12.2 Minimum required marking of pipes
37 12.3 Minimum required marking of fittings
12.4 Additional marking
38 Annex A (normative)Utilization of non-virgin PE material
A.1 Own reprocessed material from pipes and fittings
A.2 External non-virgin materials with an agreed specification
A.2.1 Material from PE pipes and fittings
39 A.2.2 Material from PE products other than pipes and fittings
40 Annex B(informative)Product standards

Related products

BS EN 1519-1:2019
$167.15