BS EN 15682-2:2013
$167.15
Glass in building. Heat soaked thermally toughened alkaline earth silicate safety glass – Evaluation of conformity/Product standard
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 40 |
This European Standard specifies requirements, the evaluation of conformity and the factory production control of flat heat soaked thermally toughened alkaline earth silicate safety glass for use in buildings.
For glass products with electrical wiring or connections for, e.g. alarm or heating purposes, other directives, e.g. Low Voltage Directive, may apply.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 7 | 1 Scope 2 Normative references |
| 8 | 3 Terms and definitions 4 Requirements 4.1 Product description |
| 9 | 4.2 Conformity with the definition of heat soaked thermally toughened alkaline earth silicate safety glass 4.3 Determination of the characteristic’s performances 4.3.1 Characteristics of heat soaked thermally toughened alkaline earth silicate safety glass 4.3.1.1 General 4.3.1.2 Characteristics of the alkaline earth silicate glass panes used for the production of heat soaked thermally toughened alkaline earth silicate safety glass |
| 10 | 4.3.2 Determination of characteristics of heat soaked thermally toughened alkaline earth silicate safety glass products 4.3.2.1 General 4.3.2.2 Safety in the case of fire – Resistance to fire |
| 11 | 4.3.2.3 Safety in the case of fire – Reaction to fire 4.3.2.4 Safety in the case of fire – External fire behaviour 4.3.2.5 Safety in use – Bullet resistance: shatter properties and resistance to attack 4.3.2.6 Safety in use – Explosion resistance: impact behaviour and resistance to impact 4.3.2.7 Safety in use – Burglar resistance: shatter properties and resistance to attack 4.3.2.8 Safety in use – Pendulum body impact resistance: shatter properties (safe breakability) and resistance to impact 4.3.2.9 Safety in use – Mechanical resistance: Resistance against sudden temperature changes and temperature differentials 4.3.2.10 Safety in use – Mechanical resistance: Resistance against wind, snow, permanent load and/or imposed loads of the glass unit 4.3.2.11 Protection against noise – Direct airborne sound reduction |
| 12 | 4.3.2.12 Energy conservation and heat retention – Thermal properties 4.3.2.13 Energy conservation and heat retention – Radiation properties: Light transmittance and reflectance 4.3.2.14 Energy conservation and heat retention – Radiation properties: Solar energy characteristics 4.4 Durability |
| 13 | 4.5 Dangerous substances 5 Evaluation of conformity 5.1 General 5.2 Initial type testing of the product (see 5.1, b)) 5.2.1 General 5.2.1.1 Introduction |
| 14 | 5.2.1.2 Multiple lines/sites 5.2.1.3 Historic data 5.2.2 Initial type testing of heat soaked thermally toughened alkaline earth silicate safety glass 5.2.2.1 General 5.2.2.2 Test specimens |
| 16 | 5.2.2.3 Test results |
| 17 | 5.2.2.4 Measurement of surface pre-stress 5.2.3 Initial type testing of characteristic’s performances 5.3 Factory production control and inspection of samples in accordance with a prescribed test plan (see 5.1, a) 1)) 5.4 Initial inspection of factory and of factory production control (see 5.1, a) 2)) |
| 18 | 5.5 Continuous surveillance and assessment of the factory production control (see 5.1, a) 3)) |
| 19 | 6 Marking and/or labelling 6.1 General 6.2 Product marking 6.3 Product characteristics 6.4 “Characteristics/performance identification paper” |
| 20 | Annex A (normative) Factory production control A.1 Factory production control requirements A.1.1 General A.1.2 Organisation A.1.2.1 Responsibility and authority A.1.2.2 Management representative for factory production control A.1.2.3 Management review A.1.3 Control system A.1.3.1 General A.1.3.2 Personnel |
| 21 | A.1.3.3 Documentation A.1.3.4 Test equipment A.1.3.5 Inspection and testing A.2 Marking A.3 Inspection and testing tables of heat soaked thermally toughened alkaline earth silicate safety glass production A.3.1 Information on Table A.1 |
| 22 | A.3.2 Production control A.3.3 Product control A.3.4 Use of proxy testing |
| 26 | Annex B (normative) Tests for factory production control B.1 Strength measurement B.1.1 Four point bending strength test B.1.1.1 Requirements B.1.1.2 Measurement method B.1.1.3 Test specimens B.1.2 Optical surface pre-stress measurement B.1.2.1 General B.1.2.2 Measurement method |
| 27 | B.2 Fragmentation test B.2.1 Requirements B.2.2 Test method |
| 28 | Annex C (informative) Provisions for voluntary involvement of third party(ies) C.1 General C.2 Voluntary tasks for third parties C.3 Marking and labelling |
| 29 | Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU Construction Products Directive ZA.1 Scope and relevant characteristics |
| 31 | ZA.2 Procedure(s) for the attestation of conformity of heat soaked thermally toughened alkaline earth silicate safety glass products ZA.2.1 System(s) of attestation of conformity |
| 33 | ZA.2.2 EC Certificate and Declaration of Conformity |
| 34 | ZA.3 CE marking and labelling |
