BS EN 1790:2013
$167.15
Road marking materials. Preformed road markings
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 42 |
This European Standard specifies construction products which are white and yellow, removable or non-removable, preformed road marking materials, under the form of tape, cold plastic, thermoplastics with or without drop-on materials, to be used for permanent and/or temporary road markings in circulation areas. Other products and colours intended for road markings are not covered in this European Standard.
This European Standard also gives specifications for the evaluation of conformity for white and yellow, removable or non-removable, preformed road materials under the form of tape, cold plastic, thermoplastics with or without drop-on materials to be used for permanent and/or temporary road markings in circulation areas including type testing and factory production control.
This European Standard includes an Annex ZA for tapes, preformed cold plastic road marking and thermoplastic road marking with and without drop-on materials with the clauses addressing the provisions of the EU Construction Product Directive for permanent road marking.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 8 | 1 Scope 2 Normative references 3 Terms and definitions |
| 10 | 4 Requirements 4.1 Tape, Preformed Cold Plastic Road Marking and Preformed Thermoplastic Road Marking without drop-on Materials 4.1.1 General 4.1.2 Day-time visibility (reflection in daylight or under road lighting) 4.1.3 Night-time visibility (retroreflection under vehicle headlamp illumination) |
| 11 | 4.1.4 Day-time visibility (Colour in daylight or under road lighting) 4.1.5 Skid resistance SRT value (only for non-structured road marking products) 4.1.6 Removability 4.1.7 Resistance to UV exposure 4.2 Preformed Thermoplastic Road Marking with drop-on Materials |
| 12 | 4.3 Durability 4.3.1 General 4.3.2 Durability on road trials 4.3.3 Durability of on wear simulator – turntable |
| 13 | 5 Test methods 5.1 Preparation 5.1.1 General 5.1.2 Preparation of samples of Tape, Preformed Cold Plastic Road Marking and Preformed Thermoplastics Road Marking without drop-on Materials 5.1.3 Preparation of samples of Preformed Thermoplastics Road Marking with drop-on Materials 5.2 Test methods for Tape, Preformed Cold Plastic Road Marking and Preformed Thermoplastics Road Marking without drop-on Materials 5.2.1 General 5.2.2 Day-time visibility (reflection in daylight or under road lighting) 5.2.3 Night-time visibility (retroreflection under vehicle headlamp illumination) |
| 14 | 5.2.4 Day-time visibility (Colour in daylight or under road lighting) 5.2.5 Skid resistance SRT value (only for non-structured road marking products) 5.2.6 Removability 5.2.7 Resistance to UV exposure 5.3 Test method for Preformed Thermoplastics Road Marking with drop-on Materials 5.4 Durability 5.4.1 General 5.4.2 Durability on road trials |
| 15 | 5.4.3 Durability on wear simulator: turntable 6 Evaluation of conformity 6.1 General 6.2 Initial type testing and Type Testing 6.2.1 General |
| 16 | 6.2.2 Test samples, testing and compliance criteria 6.2.3 Test reports |
| 17 | 6.3 Factory production control (FPC) 6.3.1 General 6.3.2 Requirements 6.3.2.1 General |
| 18 | 6.3.2.2 Equipment 6.3.2.2.1 Testing 6.3.2.2.2 Manufacturing 6.3.2.3 Raw materials and components 6.3.2.4 Design process 6.3.2.5 Traceability and marking 6.3.2.6 Controls during manufacturing process |
| 19 | 6.3.2.7 Product testing and evaluation 6.3.2.8 Non-complying products 6.3.2.9 Corrective action 6.3.2.10 Handling, storage and packaging 6.3.3 Product specific requirements |
| 20 | 6.3.4 Initial inspection of factory and of FPC |
| 21 | 6.3.5 Continuous surveillance of FPC 6.3.6 Procedure for modifications 6.3.7 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity |
| 22 | 7 Marking and labelling |
| 23 | Annex A (normative) Identification of preformed road marking materials A.1 General A.2 Ash content A.3 Fingerprinting A.3.1 General A.3.2 Thermogravimetric analysis (TGA) A.3.3 FT-IR spectroscopy of the TGA residue A.3.4 Attenuated Total Reflectance (ATR) FT-IR spectroscopy of the adhesive layer A.4 Tolerances |
| 25 | Annex B (normative) Test method for Ash content B.1 Principle B.2 Apparatus B.3 Procedure B.4 Results |
| 26 | B.5 Test report |
| 27 | Annex C (normative) Thermogravimetric analysis (TGA) C.1 Principle C.2 Apparatus and Procedure C.3 Results and Test Report |
| 29 | Annex D (normative) FT-IR spectroscopy of the TGA residue D.1 Principle D.2 Apparatus D.3 Procedure D.3.1 Sample preparation D.3.2 Recording the spectrum D.4 Results |
| 30 | Annex E (normative) Test method for ATR FT-IR spectroscopy of the adhesive layer E.1 Principle E.2 Apparatus E.3 Procedure E.4 Results |
| 31 | Annex F (normative) Preformed self-adhesive road marking – Test method for determination of mass per unit area of the adhesive F.1 Scope and field application F.2 References F.3 Sampling F.4 Apparatus F.5 Preparation of test samples F.6 Procedure F.7 Calculation and expression of results |
| 32 | F.8 Test report |
| 33 | Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive ZA.1 Scope and relevant characteristics |
| 35 | ZA.2 Procedure for the attestation of conformity of Tape, Preformed Cold Plastic and Preformed Thermoplastic without drop-on materials ZA.2.1 System of Attestation of Conformity |
| 36 | ZA.2.2 EC certificate of conformity |
| 37 | ZA.3 CE marking and labelling |
