BS ISO 12647-2:2013
$167.15
Graphic technology. Process control for the production of half-tone colour separations, proof and production prints – Offset lithographic processes
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 36 |
This part of ISO 12647 specifies a number of process parameters and their values to be applied when producing colour separations, printing formes and print production for four-colour sheet-fed and web-fed offset printing presses excluding coldset offset lithography on newsprint.
The parameters and values are chosen in view of the typical process covering the process stages “colour separation”, “proof production”, “making of the printing forme”, “OK print” and “production printing” on all kinds of commercially available production substrates.
This part of ISO 12647:
-
is directly applicable to press proof prints and printing processes that use colour separation printing formes as input;
-
is applicable to press proof prints and printing processes with more than four process colours as long as direct analogies to four-colour printing are maintained, such as for data and screening, for print substrates and printing parameters;
-
is applicable to printing on cardboard material for packaging;
-
is applicable for all kinds of drying methods such as heat-set, infrared, and ultraviolet;
-
provides references for quality assurance and quality management.
This part of ISO 12647 is not applicable to processes other than offset such as printing directly from digital data where there is no intermediate image carrier, or where the image carrier can be refreshed for each impression and thus each impression can be different in content.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Introduction |
| 9 | Section sec_1 Section sec_2 1 Scope 2 Normative references |
| 10 | Section sec_3 Section sec_3.1 Section sec_3.2 Section sec_3.3 Section sec_3.4 Section sec_4 Section sec_4.1 Section sec_4.2 Section sec_4.2.1 3 Terms and definitions 4 Requirements 4.1 General 4.2 Data files and printing formes |
| 11 | Section sec_4.2.2 Section sec_4.2.3 Section sec_4.2.4 |
| 12 | Section sec_4.2.5 Section sec_4.2.6 Section sec_4.2.7 Section sec_4.2.8 Section sec_4.3 Section sec_4.3.1 4.3 Proof or production print |
| 13 | Table tab_1 Section sec_4.3.2 Section sec_4.3.2.1 |
| 14 | Table tab_2 |
| 15 | Table tab_3 |
| 16 | Table tab_4 Section sec_4.3.2.2 Section sec_4.3.2.3 |
| 17 | Table tab_5 |
| 18 | Table tab_6 |
| 19 | Table tab_a Figure fig_1 |
| 20 | Table tab_b Figure fig_2 |
| 21 | Table tab_7 Section sec_4.3.2.4 |
| 22 | Section sec_4.3.3 Section sec_4.3.4 Section sec_4.3.4.1 Table tab_8 |
| 23 | Figure fig_3 Table tab_9 |
| 24 | Table tab_10 Section sec_4.3.4.2 Table tab_11 |
| 25 | Section sec_4.3.5 Section sec_4.3.6 |
| 26 | Section sec_5 Section sec_5.1 Section sec_5.2 5 Measurement methods 5.1 Computation of densities, CIELAB colour coordinates and CIELAB colour differences 5.2 Control strip |
| 27 | Annex sec_A Annex A (informative) Grey reproduction and grey balance |
| 28 | Table tab_d Figure fig_A.1 |
| 29 | Table tab_e Figure fig_A.2 |
| 30 | Table tab_A.1 |
| 31 | Annex sec_B Annex B (informative) Handling differences in paper colour |
| 33 | Reference ref_1 Reference ref_2 Reference ref_3 Reference ref_4 Reference ref_5 Reference ref_6 Reference ref_7 Reference ref_8 Bibliography |
