BS ISO 16143-2:2014
$189.07
Stainless steels for general purposes – Corrosion-resistant semi-finished products, bars, rods and sections
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 48 |
This part of ISO 16143 specifies the technical delivery conditions for semi-finished products, hot formed bars, rods, and sections for general purposes made of the most important corrosion-resistant stainless steel grades.
NOTE 1 Throughout this part of ISO 16143, the term “general purposes” means purposes other than the special purposes mentioned in the Bibliography.
NOTE 2 Heat-resistant steel grades can be found in ISO 4955 and they can be used for corrosion-resistant purposes.
In addition to this part of ISO 16143, the general technical delivery requirements of ISO 404 are applicable.
This part of ISO 16143 does not apply to components manufactured by further processing the product forms listed in the first paragraph above with quality characteristics altered as a result of such further processing.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Section sec_1 Section sec_2 1 Scope 2 Normative references |
| 8 | Section sec_3 Section sec_3.1 Section sec_3.2 Section sec_4 Section sec_5 3 Terms and definitions 4 Designation 5 Information to be supplied by the purchaser |
| 9 | Section sec_6 Section sec_7 Section sec_7.1 Section sec_7.2 Section sec_7.3 Section sec_7.3.1 Section sec_7.3.2 6 Classification of grades 7 Requirements 7.1 Manufacturing process 7.2 Delivery condition 7.3 Chemical composition |
| 10 | Section sec_7.4 Section sec_7.5 Section sec_7.6 Table tab_1 7.4 Susceptibility to intergranular corrosion 7.5 Mechanical properties 7.6 Surface quality |
| 11 | Section sec_7.7 Section sec_7.8 Section sec_8 Section sec_8.1 Section sec_8.2 Section sec_8.2.1 Section sec_8.2.2 Section sec_8.2.3 7.7 Internal soundness 7.8 Dimensions, tolerances on dimensions, and shape 8 Inspection, testing, and conformance of products 8.1 General 8.2 Inspection and testing procedures and types of inspection documents |
| 12 | Section sec_8.3 Section sec_8.3.1 Section sec_8.3.2 Section sec_8.3.2.1 Section sec_8.3.2.2 Section sec_8.3.2.3 Section sec_8.4 Section sec_8.4.1 Section sec_8.4.2 Section sec_8.4.3 Section sec_8.4.4 Section sec_8.4.5 8.3 Specific inspection and testing 8.4 Test methods |
| 13 | Section sec_8.4.6 Section sec_8.5 Section sec_9 Section sec_9.1 Section sec_9.2 Section sec_9.3 8.5 Retests 9 Marking |
| 14 | Table tab_2 |
| 15 | Table tab_2___1 |
| 16 | Table tab_2___2 |
| 17 | Table tab_2___3 |
| 18 | Table tab_2___4 |
| 19 | Table tab_3 |
| 20 | Table tab_4 Table tab_5 |
| 23 | Table tab_6 |
| 24 | Table tab_7 |
| 25 | Table tab_8 |
| 26 | Table tab_9 |
| 27 | Table tab_10 |
| 29 | Table tab_11 Table tab_12 |
| 30 | Table tab_13 Table tab_14 |
| 31 | Table tab_15 |
| 32 | Figure fig_1 |
| 33 | Table tab_b Figure fig_2 |
| 34 | Table tab_c Figure fig_3 |
| 35 | Annex sec_A Annex sec_A.1 Annex sec_A.2 Annex A (informative) Guidelines for further treatment (including heat treatment) in fabrication |
| 36 | Table tab_A.1 |
| 37 | Table tab_A.2 Table tab_A.3 |
| 38 | Table tab_A.4 |
| 39 | Table tab_A.5 |
| 40 | Annex sec_B Table tab_B.1 Annex B (informative) Designations of the steels given in Table 2 and of comparable grades covered in ASTM, EN, JIS, and GB Standards |
| 43 | Annex sec_C Annex C (informative) Applicable dimensional standards |
| 44 | Reference ref_1 Reference ref_2 Reference ref_3 Reference ref_4 Reference ref_5 Reference ref_6 Reference ref_7 Reference ref_8 Reference ref_9 Reference ref_10 Reference ref_11 Reference ref_12 Reference ref_13 Reference ref_14 Reference ref_15 Reference ref_16 Reference ref_17 Reference ref_18 Reference ref_19 Reference ref_20 Reference ref_21 Bibliography |
