🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS ISO 20816-4:2018

BS ISO 20816-4:2018

$142.49

Mechanical vibration. Measurement and evaluation of machine vibration – Gas turbines in excess of 3 MW, with fluid-film bearings

Published By Publication Date Number of Pages
BSI 2018 30
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This document is applicable to land-based gas turbines with fluid-film bearings and power outputs greater than 3 MW and an operating speed under load between 3 000 r/min and 30 000 r/min. In some cases (see the list of exclusions below), this includes other rotating machinery coupled either directly or through a gearbox. The evaluation criteria provided in this document are applicable to the vibration of the main input and output bearings of the gearbox but are not applicable to the vibration of the internal gearbox bearings nor to the assessment of the condition of those gears. Specialist techniques required for evaluating the condition of gears are outside the scope of this document.

This document is not applicable to the following:

  1. gas turbines with power outputs greater than 40 MW at rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min or 3 600 r/min (see ISO 20816‑2);

  2. aero-derivative gas turbines (including gas turbines with dynamic properties similar to those of aero-derivatives);

    NOTE ISO 3977‑3 defines aero-derivatives as aircraft propulsion gas generators adapted to drive mechanical, electrical or marine propulsion equipment. Large differences exist between heavy-duty and aero-derivative gas turbines, for example, in casing flexibility, bearing design, rotor-to-stator mass ratio and mounting structure. Different criteria, therefore, apply for these two turbine types.

  3. gas turbines with outputs less than or equal to 3 MW (see ISO 7919‑3 and ISO 10816‑3);

  4. turbine driven generators (see ISO 20816‑2, ISO 7919‑3 and ISO 10816‑3);

  5. turbine driven pumps (see ISO 10816‑7);

  6. turbine driven rotary compressors (see ISO 7919‑3 and ISO 10816‑3);

  7. the evaluation of gearbox vibration (see this clause) but does not preclude monitoring of gearbox vibration;

  8. the evaluation of combustion vibration but does not preclude monitoring of combustion vibration;

  9. rolling element bearing vibration.

This document establishes provisions for evaluating the severity of the following in-situ broad-band vibrations:

  1. structural vibration at all main bearing housings or pedestals measured radial (i.e. transverse) to the shaft axis;

  2. structural vibration at thrust bearing housings measured in the axial direction;

  3. vibration of rotating shafts radial (i.e. transverse) to the shaft axis at, or close to, the main bearings.

These are in terms of the following:

  • vibration under normal steady-state operating conditions;

  • vibration during other (non-steady-state) conditions when transient changes are taking place, including run up or run down, initial loading and load changes;

  • changes in vibration which can occur during normal steady-state operation.

PDF Catalog

PDF Pages PDF Title
2 National foreword
6 Foreword
7 Introduction
9 1 Scope
10 2 Normative references
3 Terms and definitions
4 Measurement procedures
4.1 General
11 4.2 Measurements of vibration of non-rotating parts
13 4.3 Measurements of vibration of rotating shafts
14 5 Evaluation criteria
5.1 General
15 5.2 Criterion I: vibration magnitude
5.2.1 General
5.2.2 Vibration magnitude at rated speed under steady-state operating conditions
17 5.2.3 Operational limits for steady-state operation
18 5.2.4 Vibration magnitude during non-steady-state conditions (transient operation)
20 5.3 Criterion II: change in vibration magnitude under steady-state conditions at rated speed
21 5.4 Supplementary procedures/criteria
5.5 Evaluation based on vibration vector information
22 Annex A (normative) Evaluation zone boundaries for vibration of non-rotating parts
23 Annex B (normative) Evaluation zone boundaries for vibration of rotating shafts
25 Annex C (informative) Example of setting ALARM and TRIP values
26 Annex D (informative) Cautionary notes about the use of vibration velocity criteria at low rotational speeds
28 Annex E (informative) Evaluation zone boundary limits and bearing clearance
29 Bibliography

Related products

BS ISO 20816-4:2018
$142.49