BS ISO 22554:2015
$102.76
Ships and marine technology. Propeller shaft revolution indicators. Electric type and electronic type
| Published By | Publication Date | Number of Pages |
| BSI | 2015 | 18 |
This International Standard specifies the construction, performance requirements, methods of testing, and required test results for electric and electronic propeller shaft revolution indicators (hereinafter referred to as “indicator system”) required by Clause 2.5.4, Regulation 19, chapter V, SOLAS 1974 (as amended, 2000).
This International Standard is associated with IMO Resolution A.694 (17) and IEC 60945.
Where a requirement in this International Standard differs from IEC 60945, the requirement in this International Standard takes precedence.
NOTE When this indicator system can be used as the tachometer for the engine of a ship, its usage as the tachometer will be accepted.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Section sec_1 Section sec_2 Section sec_3 Section sec_3.1 Section sec_3.2 1 Scope 2 Normative references 3 Terms and definitions |
| 8 | Section sec_3.3 Section sec_3.4 Section sec_3.5 Section sec_3.6 Section sec_3.7 Section sec_3.8 Section sec_4 Section sec_4.1 Section sec_4.1.1 Section sec_4.1.2 Section sec_4.1.3 Section sec_4.1.4 Section sec_4.1.5 4 Construction of indicator system 4.1 Indicator system |
| 9 | Table tab_a Figure fig_1 Section sec_4.2 Section sec_4.2.1 Section sec_4.2.2 Section sec_4.2.2.1 4.2 Transmitters |
| 10 | Section sec_4.2.2.2 Section sec_4.2.2.3 Section sec_4.2.3 Section sec_4.2.3.1 Section sec_4.2.3.2 Section sec_4.3 Section sec_4.3.1 Section sec_4.3.2 Section sec_4.3.3 Section sec_4.3.4 Section sec_4.3.5 4.3 Indicator |
| 11 | Section sec_4.3.6 Section sec_4.3.7 Section sec_4.3.8 Section sec_5 Section sec_5.1 Section sec_5.2 Section sec_5.3 Section sec_5.4 Section sec_5.5 Section sec_5.6 5 Performance requirements 5.1 General 5.2 Balance 5.3 Friction error 5.4 Calibration accuracy 5.5 Damping 5.6 Zero point |
| 12 | Section sec_5.7 Section sec_5.8 Section sec_5.8.1 Section sec_5.8.2 Section sec_5.8.3 Section sec_5.9 Section sec_5.9.1 Section sec_5.9.2 Section sec_5.9.3 Table tab_1 Section sec_5.9.4 Section sec_5.10 5.7 Output electric signal of a signal converter 5.8 Output electric signal accuracy of a signal converter 5.9 Power supply fluctuations 5.10 Insulation resistance and high voltage |
| 13 | Section sec_6 Section sec_6.1 Section sec_6.2 Section sec_6.3 Section sec_6.4 Section sec_6.5 Section sec_6.6 Section sec_6.7 6 Methods of testing and required test results 6.1 Test items and sequence 6.2 Construction 6.3 Environmental test 6.4 Balance test 6.5 Friction test 6.6 Calibration accuracy test 6.7 Damping test |
| 14 | Section sec_6.8 Section sec_6.9 Section sec_6.10 Section sec_6.11 Section sec_7 Section sec_8 Section sec_8.1 Section sec_8.2 Section sec_8.3 Section sec_9 6.8 Zero point test 6.9 Signal converter output electric signal test 6.10 Signal converter output electric signal accuracy test 6.11 Power supply fluctuation test 7 Interface 8 Marking 9 Information |
| 15 | Reference ref_1 Reference ref_2 Reference ref_3 Reference ref_4 Bibliography |
