ISO 19385:2017
$27.95
Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for water jetting or water blasting applications — Specification
| Published By | Publication Date | Number of Pages |
| ISO | 2017-10 | 18 |
ISO 19385 specifies requirements for nine classes of reinforced hydraulic hoses and hose assemblies of nominal sizes ranging from 5 to 25. Each class has a single maximum working pressure. Such hoses and hose assemblies are intended to be used with very high-pressure water jetting and water blasting machines.
ISO 19385 also reviews all the significant hazards, hazardous situations and events relevant to the equipment in the scope, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
Related products
-
BS ISO 19385:2017
Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for water jetting or water…
-
ISO 1938-1:2015
Spécification géométrique des produits (GPS) — Équipement de mesure dimensionnel — Partie 1: Calibres lisses…
-
BS EN ISO 19285:2017
Non-destructive testing of welds. Phased array ultrasonic testing (PAUT). Acceptance levels Published By Publication Date…
-
ISO 16385:2014
Huile essentielle de baie rose (Schinus areira L.), type Argentine Published By Publication Date Number…
-
BS ISO 18385:2016
Minimizing the risk of human DNA contamination in products used to collect, store and analyze…
-
ISO 1938-2:2017
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Reference disk gauges Published…
-
BS ISO 19380:2019
Heavy commercial vehicles and buses. Centre of gravity measurements. Axle lift, tilt-table and stable pendulum…
-
ISO 19585:2019
Heavy commercial vehicles and buses — Vehicle dynamics simulation and validation — Steady-state circular driving…
-
ISO 19285:2017
Non-destructive testing of welds — Phased array ultrasonic testing (PAUT) — Acceptance levels Published By…
-
ISO 19085-6:2017
Woodworking machines — Safety — Part 6: Single spindle vertical moulding machines (“toupies”) Published By…
-
ISO 19085-4:2018
Machines à bois — Sécurité — Partie 4: Scies circulaires à panneaux verticales Published By…
-
BS ISO 16385:2014
Essential oil of molle (Schinus areira L.), Argentinean type Published By Publication Date Number of…
-
ISO 19085-9:2019
Machines à bois — Sécurité — Partie 9: Scies circulaires à table de menuisier (avec…
-
ISO 19085-3:2017
Woodworking machines — Safety requirements — Part 3: Numerically controlled (NC) boring and routing machines…
-
ISO 18385:2016
Minimizing the risk of human DNA contamination in products used to collect, store and analyze…
-
ISO 13385-2:2011
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Calliper depth gauges; Design…
-
ISO 19085-2:2017
Woodworking machines — Safety — Part 2: Horizontal beam panel circular sawing machines Published By…
-
BS ISO 19685:2017
Vacuum technology. Vacuum gauges. Specifications, calibration and measurement uncertainties for Pirani gauges Published By Publication…
-
BS ISO 19365:2016
Passenger cars. Validation of vehicle dynamic simulation. Sine with dwell stability control testing Published By…
-
ISO 19085-8:2017
Machines à bois — Sécurité — Partie 8: Machines de ponçage et de calibrage à…
-
ISO 19345-1:2019
Industries du pétrole et du gaz naturel — Systèmes de transport par conduites — Spécifications…
-
BS ISO 19585:2019
Heavy commercial vehicles and buses. Vehicle dynamics simulation and validation. Steady-state circular driving behavior Published…
-
ISO 19085-10:2018
Woodworking machines — Safety — Part 10: Building site saws (contractor saws) Published By Publication…
-
ISO 13385-1:2011
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Callipers; Design and metrological…
-
ISO 14385-1:2014
Stationary source emissions — Greenhouse gases — Part 1: Calibration of automated measuring systems Published…
-
ISO 14385-2:2014
Stationary source emissions — Greenhouse gases — Part 2: Ongoing quality control of automated measuring…
-
ISO 19835:2018
Non-destructive testing — Acoustic emission testing — Steel structures of overhead travelling cranes and portal…
-
ISO 19345-2:2019
Petroleum and natural gas industry — Pipeline transportation systems — Pipeline integrity management specification —…
-
ISO 1985:2015
Machine tools — Test conditions for surface grinding machines with vertical grinding wheel spindle and…
-
ISO 13385-1:2019
Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Design and metrological characteristics…
-
ISO 19389:2014
Space data and information transfer systems — Conjunction data message Published By Publication Date Number…
-
ISO 19380:2019
Heavy commercial vehicles and buses — Centre of gravity measurements — Axle lift, tilt-table and…
-
ISO 19085-1:2017
Woodworking machines — Safety — Part 1: Common requirements Published By Publication Date Number of…
-
BS ISO 19385:2017+A1:2019
Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for water jetting or water…
-
AS ISO 18385:2017
Minimizing the risk of human DNA contamination in products used to collect, store and analyze…
-
BS ISO 19835:2018
Non-destructive testing. Acoustic emission testing. Steel structures of overhead travelling cranes and portal bridge cranes…
-
ISO 19685:2017
Vacuum technology — Vacuum gauges — Specifications, calibration and measurement uncertainties for Pirani gauges Published…
-
ISO 19085-5:2017
Woodworking machines — Safety — Part 5: Dimension saws Published By Publication Date Number of…
-
BS ISO 1985:2015
Machine tools. Test conditions for surface grinding machines with vertical grinding wheel spindle and reciprocating…
-
ISO 19085-7:2019
Woodworking machines — Safety — Part 7: Surface planing, thickness planing, combined surface/thickness planing machines…
