77.120.50 – Titanium and titanium alloys – PDF Standards Store ?u= Wed, 06 Nov 2024 05:02:16 +0000 en-US hourly 1 https://wordpress.org/?v=6.7.1 ?u=/wp-content/uploads/2024/11/cropped-icon-150x150.png 77.120.50 – Titanium and titanium alloys – PDF Standards Store ?u= 32 32 SAE MAP 4296:1993 ?u=/product/publishers/sae/sae-map-42961993/ Wed, 06 Nov 2024 05:02:16 +0000 Drawing Interpretations, Standard Machining Practice, Tube Fittings and Connectors, Fluid Systems, Metric
Published By Publication Date Number of Pages
SAE 1993-06-21 7
]]>
This SAE Metric Aerospace Recommended Practice (MAP) establishes the drawing interpretations, standard machining practice for tube fittings and connectors used in metric fluid systems.
]]> SAE MAM 4911B:2003 ?u=/product/publishers/sae/sae-mam-4911b2003/ Wed, 06 Nov 2024 05:02:04 +0000 Titanium Alloy, Sheet, Strip, and Plate, 6Al 4V, Annealed
Published By Publication Date Number of Pages
SAE 2003-03-12 9
]]> This specification covers a titanium alloy in the form of sheet,
strip, and plate procured in metric units.

AMS 4911 is the inch/pound version of this MAM.

These products have been used typically for parts requiring
strength up to 400 degrees C, but usage is not limited to such
applications.

Certain processing procedures and service conditions may cause
these products to become subject to stress-corrosion cracking; ARP
982 recommends practices to minimize such conditions.

]]> SAE MAM 2245C:2007 ?u=/product/publishers/sae/sae-mam-2245c2007/ Wed, 06 Nov 2024 05:01:47 +0000 Tolerances, Metric, Titanium and Titanium Alloy Tubing
Published By Publication Date Number of Pages
SAE 2007-08-24 11
]]> This specification covers established manufacturing tolerances applicable to titanium and titanium alloy extruded bars, rods, and shapes ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" applies only to the higher figure of the specified range.

]]> SAE MAM 2244C:2007 ?u=/product/publishers/sae/sae-mam-2244c2007/ Wed, 06 Nov 2024 05:01:46 +0000 Tolerances, Metric, Titanium and Titanium Alloy Tubing
Published By Publication Date Number of Pages
SAE 2007-07-19 5
]]> This specification covers established metric manufacturing tolerances applicable to titanium and titanium alloy tubing ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of the specified range.

]]> SAE MAM 2242D:2007 ?u=/product/publishers/sae/sae-mam-2242d2007/ Wed, 06 Nov 2024 05:01:45 +0000 Tolerances, Metric, Corrosion and Heat Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Sheet, Strip, and Plate
Published By Publication Date Number of Pages
SAE 2007-09-13 13
]]> This specification covers established manufacturing tolerances applicable to sheet, strip, and plate of corrosion and heat resistant steels, iron alloys, titanium, and titanium alloys ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term 'excl' is used to apply only to the higher figure of the specified range.

]]> SAE MAM 2241E:2007 ?u=/product/publishers/sae/sae-mam-2241e2007/ Wed, 06 Nov 2024 05:01:44 +0000 Tolerances, Metric, Corrosion and Heat Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Bars and Wire
Published By Publication Date Number of Pages
SAE 2007-07-19 10
]]> This specification covers established metric manufacturing tolerances applicable to corrosion and heat resistant steel, iron alloy, titanium, and titanium alloy bars and wire ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term 'excl' is used to apply only to the higher figure of the specified range.

]]> SAE MA 614A:1998 ?u=/product/publishers/sae/sae-ma-614a1998/ Wed, 06 Nov 2024 05:01:37 +0000 Hose Assembly, Polytetrafluoroethylene (PTFE), Metallic Reinforced, 28,000 kPa, 204 °C, Hydraulic, Metric
Published By Publication Date Number of Pages
SAE 1998-06-01 23
]]>
This SAE Aerospace Standard (AS) establishes the requirements for polytetrafluoroethylene (PTFE) hose assemblies for use in aerospace hydraulic systems at temperatures between -55 °C and 204 °C and at a nominal pressure up to 28,000 kPa (280 bar). The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated.
The use of these hose assemblies in high pressure pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this document, for example, oxygen, shall be subject to the approval of the purchaser.
]]> SAE MA 4812A:2019 ?u=/product/publishers/sae/sae-ma-4812a2019/ Wed, 06 Nov 2024 05:01:27 +0000 Insert - Thin Wall, Metric Short and Long Hole Preparation for
Published By Publication Date Number of Pages
SAE 2019-03-18 3
]]> Insert - Thin Wall, Metric Short and Long Hole Preparation for
Published By Publication Date Number of Pages
SAE 2019-03-18 3
]]> SAE MA 4623:1994 ?u=/product/publishers/sae/sae-ma-46231994/ Wed, 06 Nov 2024 05:01:23 +0000 Hose Assembly, Polytetrafluoroethylene, Para Aramid Reinforced Heavy-Duty, 21000 kPa, 135 °C, Aircraft Hydraulic Systems, Metric
Published By Publication Date Number of Pages
SAE 1994-05-01 24
]]>
This document defines the requirements for heavy-duty hose assemblies suitable for use in 21 000 kPa, 135 °C aircraft systems where rapid rate pressure pulsing and torsional/longitudinal flexing may occur in addition to normal hydraulic system loading.
]]> SAE MA 4510:1996 ?u=/product/publishers/sae/sae-ma-45101996/ Wed, 06 Nov 2024 05:01:16 +0000 Fittings, Weld, Fluid Connection, 35000 kPa, Metric
Published By Publication Date Number of Pages
SAE 1996-11-01 16
]]>
This SAE Metric Aerospace Standard (AS) establishes the requirements for weld fluid connection fittings and rings to be orbital arc welded to tubing for use in metric aircraft fluid systems at a maximum operating pressure of 35,000 kPa.
]]>