This International Standard specifies manufacturing, testing and marking requirements for solid-section fork arms, for quantity production and with all types of mounting. These include, but are not limited to, hook, shaft or pin, bolt-on and roller type fork arms.<\/p>\n
By agreement between the fork arm manufacturer and the purchaser, these requirements may also be applied to fork arms not intended for quantity manufacture.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 3<\/td>\n | TitlePage – Fork-lift trucks\ufffd\u2014 Fork arms\ufffd\u2014 Technical characteristics and testing <\/td>\n<\/tr>\n | ||||||
| 5<\/td>\n | Foreword – Foreword <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Scope – 1\ufffd\ufffd\ufffd Scope NormativeReference – 2\ufffd\ufffd\ufffd Normative references Clause1 – 4\ufffd\ufffd\ufffd Manufacture Clause1 – 5\ufffd\ufffd\ufffd Testing UntitledSubclause2 – 5.1\ufffd\ufffd\ufffd A prototype fork arm shall be subjected to, and meet the requirements… <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | UntitledSubclause2 – 5.2\ufffd\ufffd\ufffd The tests in Clause1 – 6\ufffd\ufffd\ufffd Yield test Subclause2 – 6.1\ufffd\ufffd\ufffd Test load Subclause3 – 6.1.1\ufffd\ufffd\ufffd Fork arms each of specified capacity up to and including Subclause3 – 6.1.2\ufffd\ufffd\ufffd Fork arms each of specified capacity greater than Subclause2 – 6.2\ufffd\ufffd\ufffd Procedure <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | Subclause2 – 6.3\ufffd\ufffd\ufffd Requirement Clause1 – 7\ufffd\ufffd\ufffd Impact test Subclause2 – 7.1\ufffd\ufffd\ufffd Sampling Subclause2 – 7.2\ufffd\ufffd\ufffd Procedure Subclause2 – 7.3\ufffd\ufffd\ufffd Requirement Clause1 – 8\ufffd\ufffd\ufffd Fatigue test Subclause2 – 8.1\ufffd\ufffd\ufffd Test load magnitude, frequency and duration UntitledSubclause3 – 8.1.1\ufffd\ufffd\ufffd The dynamic test load shall be of constant amplitude and have a pea… UntitledSubclause3 – 8.1.2\ufffd\ufffd\ufffd The test load frequency shall be UntitledSubclause3 – 8.1.3\ufffd\ufffd\ufffd The duration of the test shall be not less than 10 Subclause2 – 8.2\ufffd\ufffd\ufffd Procedure Subclause2 – 8.3\ufffd\ufffd\ufffd Requirement <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | Clause1 – 9\ufffd\ufffd\ufffd Surface-crack detection Clause1 – 10\ufffd\ufffd\ufffd Marking UntitledSubclause2 – 10.1\ufffd\ufffd\ufffd At the position indicated in UntitledSubclause2 – 10.2\ufffd\ufffd\ufffd The truck manufacturer’s identification and part number may be shown… <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Fork-lift trucks. Fork arms. Technical characteristics and testing<\/b><\/p>\n |