The purpose of this standard is to provide the minimum requirements for fabricated composite slide gates, including materials, general design, manufacture, testing, inspection, and shipment.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 7<\/td>\n | Foreword I.\tIntroduction. I.A.\tBackground.\u2003A fabricated composite slide gate is a vertically sliding gate with fiberglass-reinforced composite-plastic or rigid compressed-plastic slides and frames of either fiberglass-reinforced composite plastic, stainless steel, or coated carbon <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | I.B.\tHistory.\u2003The original AWWA standard for slide gates (then referred to as sluice gates) was approved as tentative on June 26, 1941 and described cast-iron gates. The tentative standard was revised and approved on June 4, 1967, as AWWA C501. Subsequent I.C.\tAcceptance.\u2003In May 1985, the US Environmental Protection Agency (USEPA) entered into a cooperative agreement with a consortium led by NSF International (NSF) to develop voluntary third-party consensus standards and a certification program for direct <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | II.\tSpecial Issues. II.A.\tChlorine and Chloramine Degradation of Elastomers.\u2003The selection of materials is critical for water service and distribution piping in locations where there is a possibility that elastomers will be in contact with chlorine or chloramines. Documented <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | III.\tUse of This Standard.\u2003It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the particular application being considered. III.A.\tPurchaser Options and Alternatives.\u2003The following items should be provided by the purchaser: <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | III.B.\tModification to Standard.\u2003Any modification to the provisions, definitions, or terminology in this standard must be provided by the purchaser. IV.\tMajor Revisions.\u2003Major revisions made to the standard in this edition include the following: <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | V.\tComments.\u2003If you have any comments or questions about this standard, please call AWWA Engineering and Technical Services at 303.794.7711; FAX at 303.795.7603; write to the department at 6666 West Quincy Avenue, Denver, CO 80235-3098; or email at standa <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | AWWA Standard SECTION 1:\u2002GENERAL Sec.\u20021.1\tScope Sec.\u20021.2\tPurpose Sec.\u20021.3\tApplication <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | SECTION 2:\u2002REFERENCES <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | SECTION 3:\u2002DEFINITIONS <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | SECTION 4:\u2002REQUIREMENTS Sec.\u20024.1\tData to Be Provided by the Supplier Sec.\u20024.2\tData to Be Provided by the Manufacturer <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | Sec.\u20024.3\tMaterials <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | Table 1\tMaterial properties <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | Sec.\u20024.4\tGeneral Design <\/td>\n<\/tr>\n | ||||||
| 31<\/td>\n | Sec.\u20024.5\tManufacture <\/td>\n<\/tr>\n | ||||||
| 32<\/td>\n | Sec.\u20024.6\tInstallation <\/td>\n<\/tr>\n | ||||||
| 33<\/td>\n | SECTION 5:\u2002 VERIFICATION Sec.\u20025.1\tInspection <\/td>\n<\/tr>\n | ||||||
| 34<\/td>\n | Sec.\u20025.2\tTest Procedures Sec.\u20025.3\tBasis for Rejection SECTION 6:\u2002DELIVERY Sec.\u20026.1\tMarking <\/td>\n<\/tr>\n | ||||||
| 35<\/td>\n | Sec.\u20026.2\tShipment Sec.\u20026.3\tAffidavit of Compliance <\/td>\n<\/tr>\n | ||||||
| 37<\/td>\n | APPENDIX A Force Required to Actuate Fabricated Composite Gates <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" AWWA C563-21 Fabricated Composite Slide Gates<\/b><\/p>\n |