BS EN IEC 61169-69:2024
$167.15
Radio-frequency connectors – Sectional specification for RF coaxial connectors with push on mating. Characteristic impedance 50 Ω (type SMP3)
| Published By | Publication Date | Number of Pages |
| BSI | 2024 | 38 |
IEC 61169-69:2024, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with push-on coupling, typically for use in 50 Ω RF cables or micro-strips in microwave, telecommunication, wireless systems, and other fields (SMP3). It specifies mating face dimensions for general purpose connectors – grade 2, dimensional details of standard test connectors-grade 0, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series SMP3 RF connectors. This specification indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H. The SMP3 push-on coupling structure series RF coaxial connectors with the characteristic of normative impedance 50 Ω are used with various kinds of RF cables or micro-strips in microwave, telecommunication, wireless systems, and other fields. The operating frequency limit is up to 65 GHz. NOTE Imperial dimensions are the original dimensions since this is a very miniature RF connector. There is a concern that conversion to the metric system could lead to rounding errors which can lead to performance degradation from the original imperial design. The SMPM connector was released as an imperial design for this reason. All undimensioned pictorial information is for reference only.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | undefined |
| 5 | Annex ZA (normative)Normative references to international publicationswith their corresponding European publications |
| 6 | English CONTENTS |
| 8 | FOREWORD |
| 10 | 1 Scope 2 Normative references 3 Terms and definitions |
| 11 | 4 Mating face and gauge information 4.1 Dimensions – General connectors – Grade 2 4.1.1 SMP3 connector with pin-centre contact Figures Figure 1 – SMP3 connector with pin-centre contact – Full detent Tables Table 1 – Dimensions of SMP3 connector with pin-centre contact – Full detent |
| 12 | 4.1.2 SMP3 connector with socket-centre contact Figure 2 – SMP3 connector with pin-centre contact – Smooth bore Table 2 – Dimensions of SMP3 connector with pin-centre contact – Smooth bore |
| 13 | Figure 3 – SMP3 connector with socket-centre contact Table 3 – Dimensions of SMP3 connector with socket-centre contact |
| 14 | 4.2 SMP3 gauges 4.2.1 SMP3 gauge pin for socket-centre contact Figure 4 – SMP3 gauge pin for socket-centre contact Table 4 – Dimensions of SMP3 gauge pin for socket-centre contact |
| 15 | 4.2.2 Gauges for outer contact of SMP3 connector with socket-centre contact Figure 5 – SMP3 engagement force gauge – Full detent |
| 16 | Table 5 – Dimensions of SMP3 engagement force gauge – Full detent |
| 17 | Figure 6 – SMP3 separation force gauge – Full detent |
| 18 | Table 6 – Dimensions of SMP3 separation force gauge – Full detent |
| 19 | Figure 7 – SMP3 engagement force gauge – Smooth bore |
| 20 | Table 7 – Dimensions of SMP3 engagement force gauge – Smooth bore |
| 21 | Figure 8 – SMP3 Separation force gauge – Smooth bore |
| 22 | Table 8 – Dimensions of SMP3 separation force gauge – Smooth bore |
| 23 | Figure 9 – SMP3 gauge block Table 9 – Dimensions of SMP3 gauge block |
| 24 | 5 Quality assessment procedure 5.1 General 5.2 Rating and characteristics (see IEC 61169-1:2013, Clause 5) Tableٞ 10 – Preferred climatic categories |
| 25 | Table 11 – Rating and characteristics |
| 27 | 5.3 Test schedule and inspection requirements 5.3.1 Acceptance tests Table 12 – Acceptance tests |
| 28 | 5.3.2 Periodic tests Table 13 – Periodic tests |
| 29 | 5.4 Procedures for the quality conformance 5.4.1 Quality conformance inspection 5.4.2 Quality conformance and its maintenance |
| 30 | 6 Instructions for preparation of detail specifications (DS) 6.1 General 6.2 Identification of the component 6.3 Performances 6.4 Marking, ordering information and related matters |
| 31 | 6.5 Selection of tests, test conditions and severities 6.6 Blank detail specification pro-forma for type SMP3 connector |
| 35 | 7 Marking 7.1 Marking of component |
| 36 | 7.2 Marking and contents of package |
