ASTM-B69 2011(Redline)

$26.65

B69-11 Standard Specification for Rolled Zinc (Redline)

Published By	Publication Date	Number of Pages
ASTM	2011	5

Guaranteed Safe Checkout

Categories: 77.120.60 - Lead, zinc, tin and their alloys, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

Abstract

This specification covers two types of commercial rolled zinc. Type I are coils or sheets cut from strip rolled zinc, and Type II are zinc plates such as boiler and hull plates produced by any rolling method. The products shall be produced by casting, rolling, and other processes found in mill product plant. The material shall be tested and conform to the required chemical composition. The testing of wrought zinc for determination of tensile properties shall be conducted. The testing of zinc for hardness shall be made on a Rockwell superficial hardness tester or on a microhardness tester. The determination of chemical composition shall be performed by either an appropriate chemical method or by optical emission spectrographic methods.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers two types of commercial rolled zinc as described in 1.2. It should be understood that the specification is general. Any closer limitations on permissible variations shall be a matter of agreement between the supplier (manufacturer) and the purchaser.

1.2 Rolled zinc is furnished in two types as follows:

1.2.1 Type I — Coils or sheets cut from strip (ribbon) rolled zinc and

1.2.2 Type II — Zinc plates such as boiler and hull plates produced by any rolling method.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

B899 Terminology Relating to Non-ferrous Metals and Alloys E8 Test Methods for Tension Testing of Metallic Materials E18 Test Methods for Rockwell Hardness of Metallic Materials E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition E60 Practice for Analysis of Metals, Ores, and Related Materials by Spectrophotometry E88 Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition E384 Test Method for Knoop and Vickers Hardness of Materials E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) E536 Test Methods for Chemical Analysis of Zinc and Zinc Alloys E634 Practice for Sampling of Zinc and Zinc Alloys by Spark Atomic Emission Spectrometry

ISO Standards

ISOÃ¢Â€Â‰3815-2 Zinc and zinc alloys–Part 2: Analysis by inductively coupled plasma optical emission spectrometry

Keywords

architectural rolled zinc, Type 1; architectural rolled zinc, Type 2; rolled zinc; zinc; zinc alloys; zinc plate; zinc sheet: Rolled zinc; Zinc plate/sheet; Temper; Zinc–specifications;

ICS Code

ICS Number Code 77.120.60 (Lead, zinc, tin and their alloys)

DOI: 10.1520/B0069-11 ASTM International is a member of CrossRef.

ASTM B69 (Nonferrous Metal Standards and Nonferrous Alloy Standards)

Citing ASTM Standards

[Back to Top]

Additional information

Standard Title	B69-11 Standard Specification for Rolled Zinc (Redline)
Published Code	ASTM
Publication Date	2011
Pages Count	5
ICS Codes	77.120.60 - Lead, zinc, tin and their alloys

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-B69 2011(Redline)

ASTM B69 (Nonferrous Metal Standards and Nonferrous Alloy Standards)

Related products