ASTM-F2434 2009

$40.63

F2434-09 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing

Published By	Publication Date	Number of Pages
ASTM	2009	6

Guaranteed Safe Checkout

Categories: 23.040.45 - Plastics fittings, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM F2434-09

Historical Standard: Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing

ASTM F2434

Scope

1.1 This specification covers metal insert fittings with o-ring seals and copper crimp rings for use with Cross-linked Polyethylene (PEX) and Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) tubing in ¹/_2, ³/_4, 1, and 1¼ in. nominal diameters that meet the requirements for Specifications F876 and F2262. These fittings are intended for use in 125 psi (861.9 kPa) (PEX-AL-PEX) and 100 psi (689.5 kPa) (PEX) cold- and hot-water distribution systems operating at temperatures up to and including 180°F (82°C). Included are the requirements for materials, workmanship, dimensions, performance, and markings to be used on the fittings and rings.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 Compliance with this specification requires that these fittings be tested and certified to Specification F877 and F2262.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Keywords

cold and hot water distribution; copper crimp rings; cross-linked polyethylene; metal insert fittings; PEX; PEX-AL-PEX; Crimp rings–copper; Crosslinked polyethylene (PEX) pipe/tube; Metal insert fittings; PEX/AL/PEX pipe/tube

ICS Code

ICS Number Code 23.040.45 (Plastic fittings)

DOI: 10.1520/F2434-09

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents
2	Terminology Classification Materials and Manufacture General Requirements Dimensions Workmanship, Finish and Appearance Assembly
3	FIG. 1 FIG. 2
4	Product Marking FIG. 3 FIG. 4 TABLE 1
5	Quality Assurance Keywords X1. GO/NO-GO CRIMP GAGE X1.1 X1.2 X1.3 Use of the Crimp GO/NO-GO Gage
6	FIG. X1.1

Additional information

Standard Title	F2434-09 Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Cross-linked Polyethylene/Aluminum/Cross-linked Polyethylene (PEX-AL-PEX) Tubing
Published Code	ASTM
Publication Date	2009
Pages Count	6
ICS Codes	23.040.45 - Plastics fittings