BS EN 14064-1:2018 – TC:2020 Edition
$258.95
Tracked Changes. Thermal insulation products for buildings. In-situ formed loose-fill mineral wool (MW) products – Specification for the loose-fill products before installation
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 0 |
This document specifies the requirements for blown and injected loose-fill mineral wool products for in situ installation in lofts, masonry cavity walls and frame constructions. This document is a specification for the insulation products before installation. It describes the product characteristics and includes procedures for testing, marking and labelling. This document does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards. NOTE To avoid water penetration in masonry walls special tests adjusted to local climate might be needed. This document does not cover factory made mineral wool (MW) insulation products or in situ products intended to be used for the insulation of building equipment and industrial installations. Products with a declared thermal resistance lower than 0,25 m2·K/W or a declared thermal conductivity greater than 0,060 W/(m·K) at 10 °C are not covered by this document. This document does not cover products intended for airborne sound insulation and for acoustic absorption applications.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | compares BS EN 14064-1:2018 |
| 2 | TRACKED CHANGES Text example 1 — indicates added text (in green) |
| 82 | undefined |
| 89 | 1 Scope 2 Normative references |
| 90 | 3 Terms, definitions, symbols and abbreviations 3.1 Terms and definitions |
| 91 | 3.2 Symbols and abbreviations |
| 92 | 4 Characteristics 4.1 General 4.2 For all applications 4.2.1 Thermal conductivity − Thermal resistance |
| 93 | 4.2.2 Weight of the sale unit 4.2.3 Settlement 4.2.3.1 General 4.2.3.2 Lofts |
| 94 | 4.2.3.3 Walls, masonry walls and frame constructions (closed cavities) 4.2.4 Reaction to fire 4.2.5 Durability characteristics 4.2.5.1 General 4.2.5.2 Durability of reaction to fire against ageing/degradation 4.2.5.3 Durability of thermal conductivity against ageing/degradation |
| 95 | 4.2.5.4 Durability of thermal resistance against ageing/degradation 4.3 For specific applications 4.3.1 General 4.3.2 Airflow resistivity 4.3.3 Water absorption 4.3.4 Water vapour diffusion resistance 4.3.5 Reaction to fire of product in standardized assemblies simulating end-use applications 4.3.6 Release of dangerous substances |
| 96 | 4.3.7 Continuous glowing combustion 5 Test methods 5.1 Sampling 5.2 Conditioning 5.3 Testing 5.3.1 General |
| 97 | 5.3.2 Thermal resistance and thermal conductivity |
| 98 | 5.3.3 Reaction to fire 6 Designation code 6.1 General 6.2 Assessment and Verification of the Constancy of Performance (AVCP) |
| 99 | 6.3 Factory production control 7 Marking and labelling |
| 102 | Annex A (normative)Determination of the declared values of thermal resistance and thermal conductivity A.1 General A.2 Input data A.3 Declared values A.3.1 General A.3.2 Case where thermal resistance and thermal conductivity are declared |
| 106 | Annex B (normative)Factory production control |
| 108 | Annex C (normative)Specimen preparation method for thermal resistance and thermal conductivity test C.1 Principle C.2 Procedure C.2.1 Specimen preparation method for attics floors application- case where manufacturer will base lambda declaration on density fractile (minimum density not specified) |
| 109 | C.2.2 Specimen preparation method for closed cavities or ATTICS application when an installed density is specified (see Annex A method 1 definition) |
| 111 | Annex D (normative)Specimen preparation method for water absorption test D.1 Principle D.2 Procedure |
| 112 | Annex E (normative)Specimen preparation method for air flow resistivity test — Principle |
| 113 | Annex F (normative)Testing for reaction to fire of products F.1 Scope F.2 Product and installation parameters |
| 114 | F.3 Standardized Mounting and fixing F.3.1 Test specimens for EN ISO 119252 (Ignitability) and EN 13823 (SBI) F.3.2 EN ISO 119252 (Ignitability) F.3.3 EN 13823 (SBI) |
| 115 | Annex G .(normative)Testing for reaction to fire of products in standardized assemblies simulating end-use application(s) G.1 Scope G.2 Product and installation parameters |
| 116 | G.3 Standardized Mounting and fixing G.3.1 Test specimens for EN ISO 119252 (Ignitability) and EN 13823 (SBI) G.3.2 EN ISO 119252 (Ignitability) G.3.3 EN 13823 (SBI) |
| 117 | Annex H (normative)Rules for creating performance charts for loose-fill insulation and examples of performance charts H.1 General H.2 Performance chart for loft application when method 1 or 2 (Annex A) are used H.2.1 Preliminary data and calculations H.2.2 Calculating values of performance chart |
| 120 | H.3 Performance chart for masonry cavity wall insulation, and frame constructions insulation (method 1 Annex A) |
| 122 | Annex I (normative)Specimen preparation method for coverage and density measurement I.1 Principle I.2 Procedure for attics floors application |
| 123 | I.3 Procedure for closed construction |
| 128 | Annex J (normative)Thermal insulating products for lofts and closed cavities – Determination of settlement for blown or injected loose fill insulation J.1 Settlement after ageing J.1.1 Principle J.1.2 Case of products for attics floors J.1.2.1 Apparatus J.1.2.2 Test specimens |
| 129 | J.1.3 Case of products for closed cavities (masonry cavity walls and frame constructions) J.1.3.1 Apparatus |
| 130 | J.1.3.2 Operating procedure for filling the test specimen |
| 131 | J.1.3.3 Number of test specimens J.1.3.4 Conditioning of test specimens J.1.4 Test procedure J.1.5 Calculations and expression of results |
| 132 | J.2 Test report |
| 133 | Annex K (informative)Masonry cavity walls – Method for determining suitable spacings for blowing holes K.1 Test house K.2 Test method K.3 Observations K.4 Installation procedure |
| 135 | Annex ZA (informative)Relationship of this European Standard with Regulation (EU) No.305/2011 |
