🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 60317-0-10:2017

BS EN 60317-0-10:2017

$142.49

Specifications for particular types of winding wires – General requirements. Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated, bare or enamelled round copper wire

Published By Publication Date Number of Pages
BSI 2017 26
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This part of IEC 60317 specifies the general requirements of polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated bare, grade 1 or grade 2 or enamelled round copper winding wires.

The range of nominal conductor dimensions is given in Table 1, Table 2, Table A.1 and Table A.2.

PDF Catalog

PDF Pages PDF Title
2 National foreword
5 Annex ZA(normative)Normative references to international publicationswith their corresponding European publications
7 FOREWORD
9 INTRODUCTION
10 1 Scope
2 Normative references
3 Terms, definitions, general notes and appearance
3.1 Terms and definitions
11 3.2 General notes
3.2.1 Methods of test
12 3.2.2 Winding wire
3.3 Appearance
4 Dimensions
4.1 Conductor diameter
13 Tables
Table 1 – Dimensional requirements of (single) polyester glass-fibre wound fused and unvarnished or resin or varnish impregnated over grade 1 or grade 2 enamelled round copper winding wire (R20)
14 4.2 Out of roundness of conductor
4.3 Minimum increase in diameter due to the covering
4.4 Maximum overall diameter
Table 2 – Dimensional requirements of (double) polyester glass-fibre wound fused and unvarnished or resin or varnish impregnated over bare, grade 1, or grade 2 enamelled round copper winding wire (R20)
15 5 Electrical resistance
6 Elongation
7 Springiness
7.1 Nominal conductor diameters up to and including 1,600 mm
7.2 Nominal conductor diameters over 1,600 mm
8 Flexibility and adherence
8.1 Mandrel winding test
8.2 Adherence test
Table 3 – Elongation
Table 4 – Mandrel winding
16 9 Heat shock
10 Cut-through
11 Resistance to abrasion
12 Resistance to solvents
13 Breakdown voltage
13.1 Polyester glass fibre covered bare round copper wire
13.2 Polyester glass fibre covered enamelled round copper wire
Table 5 – Breakdown voltage for bare round copper wire
17 14 Continuity of insulation
15 Temperature index
16 Resistance to refrigerants
17 Solderability
18 Heat or solvent bonding
19 Dielectric dissipation factor
20 Resistance to transformer oil
21 Loss of mass
Table 6 – Breakdown voltage for enamelled round copper wire
18 23 Pin hole test
30 Packaging
19 Annex A (informative) Diameters for intermediate nominal conductor diameters (R40)
Table A.1 – Diameters for single polyester glass-fibre wound fusedand unvarnished or resin or varnish impregnated over grade 1or grade 2 enamelled round copper wire (R40)
20 Table A.2 – Diameters for double polyester glass-fibre wound fusedand unvarnished or resin or varnish impregnated over bare,grade 1 or grade 2 enamelled round copper wire (R40)
21 Annex B (informative) Resistance
B.1 Determination of nominal resistance
Table B.1 – Electrical resistance
22 Annex C (informative) High temperature failure
23 Bibliography

Related products

BS EN 60317-0-10:2017
$142.49