BS EN 61169-58:2016:2018 Edition
$142.49
Radio-frequency connectors – Sectional specification for RF coaxial connectors with blind-mate coupling. Characteristic impedance 50 Ω (type SBMA)
| Published By | Publication Date | Number of Pages |
| BSI | 2018 | 32 |
This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for SBMA series coaxial connectors with blind-mate coupling.
The connectors are used with cables with characteristic impedance 50 Ω in an operating frequency range up to 28 GHz. The connectors are widely used in communications, antennas, radars and other applications for modules interconnections. It is also normally used in conjunction with appropriate transmission line.
It describes the interface dimensions for general purpose connectors with gauging information and the mandatory tests selected from IEC 61169-1, applicable to all detail specifications relative to type SBMA connectors.
This specification indicates the recommended performance characteristics to be considered when writing a DS and covers all tests schedules and inspection requirements.
NOTE Dimension are in mm, however original dimensions were in inches.
All un-dimensioned pictorial configurations are for reference purpose only.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | undefined |
| 7 | English CONTENTS |
| 9 | FOREWORD |
| 11 | 1 Scope 2 Normative references |
| 12 | 3 Mating face and gauge information 3.1 Dimensions – General connectors 3.1.1 Connector with socket centre contact Figures Figure 1 – Connector with pin centre contact (for dimensions, see Table 1) |
| 13 | 3.1.2 Connector with socket-centre contact Figure 2 – Connector with socket centre contact (for dimensions, see Table 2) Tables Table 1 – Dimensions of connector with pin-centre contact |
| 14 | 3.2 Gauges for general purpose connectors 3.2.1 Gauge pins for socket centre contact Figure 3 – Gauge pin for socket-centre contact (for dimensions, see Table 3) Table 2 – Dimensions of connector with socket-centre contact Table 3 – Gauge pins dimensions for socket-centre contact |
| 15 | 3.2.2 Test procedure 3.2.3 Gauge pins for outer contact Figure 4 – Gauge pin for outer contact (for dimensions, see Table 4) Table 4 – Gauge pins dimensions for outer contact |
| 16 | 3.2.4 Test procedure 3.3 Dimensions – standard test connectors – grade 0 3.3.1 Connector with pin-centre contact Figure 5 – Connector with pin centre contact (for dimensions, see Table 5) Table 5 – Dimensions of connector with pin-centre contact |
| 17 | 3.3.2 Connector with socket-centre contact 3.4 Requirements for installation 3.4.1 Radial misalignment Figure 6 – Connector with socket centre contact (for dimensions, see Table 6) Table 6 – Dimensions of connector with socket-centre contact |
| 18 | 3.4.2 Axial separation between mating reference planes Figure 7 – Radial misalignment Figure 8 – Rigidly mounted receptacle and jack |
| 19 | 4 Quality assessment procedures 4.1 General 4.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013) Figure 9 – Rigidly mounted receptacle and float mounted jack |
| 20 | Table 7 – Rating and characteristics |
| 21 | 4.3 Test schedule and inspection requirements 4.3.1 Acceptance tests 4.3.2 Periodic tests |
| 22 | Table 8 – Acceptance tests |
| 23 | Table 9 – Periodic tests |
| 24 | 4.4 Procedures for the quality conformance 4.4.1 Quality conformance inspection 4.4.2 Qualification approval and its maintenance 5 Instructions for preparation of detail specifications 5.1 General 5.2 Identification of the component 5.3 Performances |
| 25 | 5.4 Marking, ordering information and related matters 5.5 Selection of tests, test conditions and severities 5.6 Blank detail specification pro-forma for type SMBA connector |
| 29 | 6 Marking 6.1 Marking of component |
| 30 | 6.2 Marking and contents of package |
