BS ISO 1268-2:2001
$86.31
Fibre-reinforced plastics. Methods of producing test plates – Contact and spray-up moulding
| Published By | Publication Date | Number of Pages |
| BSI | 2001 | 14 |
This part of ISO 1268 specifies methods for preparing reinforced plastics test plates either by contact moulding or by spray-up moulding.
It applies exclusively to glass reinforcements.
It is intended to be read in conjunction with ISO 1268-1.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 3 | Fibre-reinforced plastics�— Methods of producing test plates�— |
| 5 | Contents Page |
| 6 | Foreword |
| 7 | Fibre-reinforced plastics�— Methods of producing test plates�— 1��� Scope 2��� Normative references 3��� Health and safety 4��� Principle 4.1��� Contact moulding |
| 8 | 4.2��� Spray-up moulding 5��� Materials 5.1��� Contact moulding 5.1.1��� Layers of reinforcing material 5.1.2��� Thermosetting resin and curing agents 5.1.3��� Release agent 5.2��� Spray-up moulding 5.2.1��� Roving or yarn packages 5.2.2��� Pre-activated thermosetting resin 5.2.3��� Catalyst 5.2.4��� Release agent 6��� Plate dimensions 6.1��� General 6.2��� Contact moulding 6.3��� Spray-up moulding |
| 9 | 7��� Reinforcement content 7.1��� General 7.2��� Contact moulding 7.3��� Spray-up moulding 8��� Apparatus 8.1��� Contact moulding 8.1.1��� Scissors 8.1.2��� Balance 8.1.3��� Beakers 8.1.4��� Brushes 8.1.5��� Mohair or steel rollers 8.1.6��� Rigid flat plate 8.1.7��� Ventilated oven 8.1.8��� Desiccator 8.2��� Spray-up moulding 8.2.1��� Glass-chopper/spray-gun unit 8.2.2��� Stopwatch |
| 10 | 9��� Procedure 9.1��� Contact moulding 9.1.1��� Prepare the test plate using the same parameters (number of layers, orientation, glass f… 9.1.2��� Coat the plate or mould on which the laminate will be made with a layer of release agent… 9.1.3��� Cut layers of reinforcement to the dimensions necessary to give a surface area large eno… 9.1.4��� Determine the total mass 9.1.5��� Determine the amount of resin 9.1.6��� Condition the resin to the temperature of the laminating room before addition of the cur… 9.1.7��� Apply a thin layer of resin and spread evenly over a surface area equivalent to the lami… 9.1.8��� When all the layers have been applied, proceed to the curing of the plate (see 9.2��� Spray-up moulding 9.2.1��� Insert the specified type of glass fibre roving into the chopper and adjust the pressure… 9.2.2��� Fill the dispenser tanks of the equipment with the pre-activated resin and the catalyst. |
| 11 | 9.2.3��� Operate the chopper for exactly 9.2.4��� Coat the plate or mould on which the laminate will be made with a layer of release agent… 9.2.5��� Apply regular layers of chopped fibres and resin, rolling after the application of each … 9.2.6��� When the required thickness has been reached, proceed to the curing of the plate (see 9.3��� Curing conditions 10��� Verification of the characteristics of the plate obtained 11��� Marking 12��� Test plate preparation report |
| 13 | Estimation of the number of reinforcement layers for various reinforcement materials A.1��� Calculation method A.2��� Product method |
