IEEE 1566-2015

$77.46

IEEE Standard for Performance of Adjustable-Speed AC Drives Rated 375 kW and Larger

Published By	Publication Date	Number of Pages
IEEE	2015	74

Guaranteed Safe Checkout

Category: IEEE

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

Revision Standard – Active. AC adjustable speed drive (ASD) systems rated above 375 kW and above 750 V output voltage as used in petrochemical and similar applications are applicable to this standard. Performance requirements for an ASD system including, but not limited to, input transformer or reactor as required, power electronics, control interfaces, cooling system, switchgear, and motor are covered. Requirements for power quality, engineering analysis, start-up assistance, training, and spare parts are also included. Certain items such as the motor, switchgear, or transformer may be excluded from the scope of vendor supply if specified in the data sheets; any special requirements for the excluded equipment shall be given by the system vendor.

PDF Catalog

PDF Pages	PDF Title
1	IEEE Std 1566™-2015 Front Cover
3	Title page
5	Important Notices and Disclaimers Concerning IEEE Standards Documents
8	Participants
10	Introduction
11	Contents
15	Important Notice 1. Overview 1.1 Scope 1.2 Purpose
16	1.3 Application
17	2. Normative references
18	3. Definitions, acronyms and abbreviations 3.1 Definitions 3.2 Acronyms and abbreviations
19	4. Safety 4.1 General 4.2 ASD construction requirements
21	5. Unit construction 5.1 ASD structure 5.2 Insulation 5.3 Nameplate
22	5.4 Rectifier 5.5 DC link 5.6 Inverter
23	5.7 Modular system 6. Adjustable speed operation 6.1 Power supply 6.2 Harmonics 6.3 Capacity
24	6.4 Performance 6.5 Grounding
25	6.6 Rating of supply 6.7 Transient over-voltages 6.8 Voltage sags
26	6.9 ASD supply voltage ride through 6.10 Loss of voltage
27	6.11 Three-phase voltage swells 6.12 Voltage distortion 6.13 Voltage unbalance
28	6.14 Common-mode voltage 6.15 Power-factor correction capacitors—switching transients 6.16 Harmonic distortion
29	6.17 Electromagnetic interference and radio-frequency interference 6.18 Acoustic noise level 7. Control 7.1 General
30	7.2 Local control 7.3 Remote control (general)
31	7.4 Bypass operation
32	8. Input transformer or reactor 8.1 Transformer
33	8.2 Reactor 9. Motor 9.1 Specification
34	9.2 Temperatures 9.3 Synchronous motor 9.4 Retrofit
35	10. Switchgear and starters 10.1 Requirements 10.2 Switchgear supply 11. Cooling system 11.1 Cooling system equipment 11.2 Air cooling
36	11.3 Liquid cooling
37	12. System coordination 12.1 Responsibility 12.2 Compatibility 13. Engineering studies 13.1 General 13.2 Studies to determine process or driven equipment requirements 13.3 Power-system analysis to determine system response to ASD 13.4 Studies to determine system mechanical constraints 13.5 Studies to determine heating or cooling constraints 13.6 Reliability analysis
38	14. Inspection and factory tests 14.1 Records 14.2 Test plan
39	14.3 Motor tests 14.4 System test
40	14.5 Testing of synchronous motor applications 15. Shipping, Handling and Storage Requirements
41	16. Commissioning and startup assistance 16.1 Commissioning plan 16.2 Field service
42	16.3 Results 16.4 Training 17. Spare parts 18. Data interchange
44	Annex A (normative) MV adjustable-speed drives electrical data sheets for purchasers
48	Annex B (normative) MV adjustable-speed drives electrical data sheets for manufacturers
52	Annex C (informative) Technical data sheet guide C.1 General C.2 Project reference, date C.3 Reference single-line diagram (SLD)
53	C.4 System of units C.5 Supply system voltage C.6 Short-circuit level C.7 Line frequency C.8 ASD auxiliary three-phase power C.9 Control power C.10 ASD continuous rating
54	C.11 Load/application requirements C.12 Harmonics C.13 System grounding C.14 Ground fault detection provided in upstream switchgear
55	C.15 Design standards C.16 Site environment C.17 ASD to be mounted in a pre-fabricated building C.18 Enclosure C.19 Incoming and load cable details
56	C.20 Finish C.21 Redundancy C.22 Voltage sag ride-through C.23 Flying restart C.24 Noise level C.25 Local control
57	C.26 Motor/transformer protection relays to be mounted in an ASD enclosure C.27 Discrete I/O C.28 4-ma to 20-mA isolated analog outputs C.29 Communication options C.30 Remote C.31 Bypass operation
58	C.32 Input transformer/reactor C.33 Motor C.34 Breakaway torque
59	C.35 Speed regulation C.36 Torque mode C.37 ASD cooling methods C.38 Testing C.39 Shipping, storage, and handling
60	C.40 Services C.41 Nameplate data C.42 Special Applications C.43 Classified locations C.44 Long cable applications C.45 Marine and offshore facilities
61	C.46 Local generation/limited supply
62	Annex D (informative) Engineering studies: typical requirements (tutorial only) D.1 Process or driven equipment requirements D.2 System response to ASD D.3 Rotational dynamics
63	D.4 Torsional analysis D.5 Information required for a torsional analysis
64	D.6 Studies to determine the heating or cooling requirements
65	Annex E (informative) Specialized applications E.1 Background E.2 Classified locations
66	E.3 Long cable applications
67	E.4 Marine and offshore facilities
69	E.5 Local generation/limited supply
71	Annex F (informative) Bibliography
74	Back Cover