ISO 2566-2:1984
$41.60
Acier — Conversion des valeurs d’allongement — Partie 2: Aciers austénitiques
| Published By | Publication Date | Number of Pages |
| ISO | 1984-08 | 32 |
Specifies a method of converting room temperature percentage elongations after fracture obtained on various proportional and non-proportional gauge lengths to other gauge lengths. The conversions are not applicable to cold reduced steels, quenched and tempered steels and non-austenitic steels, or where certain tensile strength ranges and dimensions are exceeded.
Related products
-
BS EN ISO 2566-1:1999
Steel. Conversion of elongation values – Carbon and low alloy steels Published By Publication Date…
-
BS 6337-4:1984
General methods of chemical analysis – Method for determination of chloride ions by potentiometry Published…
-
BS 6200-3.12.3:1986
Sampling and analysis of iron, steel and other ferrous metals. Methods of analysis. Determination of…
-
BS 3364:1980
Specification for dental zinc phosphate cement Published By Publication Date Number of Pages BSI 1980…
-
BS 7020-2:1988:1989 Edition
Analysis of iron ores – Method for the determination of hygroscopic moisture in analytical samples…
-
BS 1127-1:1990
Screwing dies and dienuts – Specification for hand- and machine-operated circular screwing dies and hand-operated…
-
ASHRAE Fundamentals Handbook IP 2013
2013 ASHRAE Handbook – Fundamentals – IP Edition Published By Publication Date Number of Pages…
-
BS ISO 7764:2006
Iron ores. Preparation of predried test samples for chemical analysis Published By Publication Date Number…
-
BS 6950:1988
Specification for a standard reference zero for the calibration of pure tone bone conduction audiometers…
-
BS ISO 4903:1989:1990 Edition
Information technology. Data communication. 15-pole DTE/DCE interface connector and contact number assignments Published By Publication…
-
ISO 2566-1:1984
Steel — Conversion of elongation values — Part 1: Carbon and low alloy steels Published…
-
BS ISO 2596:2006
Iron ores. Determination of hygroscopic moisture in analytical samples. Gravimetric, Karl Fischer and mass-loss methods…
-
BS ISO 2596:1994:1995 Edition
Iron ores. Determination of hygroscopic moisture in analytical samples. Gravimetric and Karl Fischer methods Published…
-
BS EN ISO 6845:2003
Surface active agents. Technical alkane sulfonates. Determination of mean relative molecular mass and content of…
-
BS 5050:1974
Methods of test for cryolite Published By Publication Date Number of Pages BSI 1974 20
-
BS 6783-2:1986
Sampling and analysis of nickel, ferronickel and nickel alloys – Method for determination of nickel…
-
BS 7161:1990
Specification for propeller shaft ends and bosses for inboard-engined pleasure craft Published By Publication Date…
-
BS 6104-1:1981:1984 Edition
Mechanical properties of fasteners – Specification for bolts, screws and studs Published By Publication Date…
-
BS 4361-21:1989
Woodworking machines – Specification for turning lathes Published By Publication Date Number of Pages BSI…
-
BS 4196-0:1981
Sound power levels of noise sources – Guide for the use of basic standards and…
-
BS 1972:1967:1983 Edition
Specification for polythene pipe (Type 32) for above ground use for cold water services Published…
-
BS EN 635-1:1995
Plywood. Classification by surface appearance – General Published By Publication Date Number of Pages BSI…
-
BS 6296:1982
Glossary of terms for self-propelled crawler and wheel tractors and their equipment used for earth-moving…
-
BS 6200-3.20.4:1986
Sampling and analysis of iron, steel and other ferrous metals. Methods of analysis. Determination of…
-
BS 2M 52:1989
Method for impulse testing of hydraulic hose, tubing and fitting assemblies for aerospace fluid systems…
-
BS 5072-8:1980
Methods of test for sodium fluoride for industrial use – Determination of chlorides content Published…
-
BS 4965:1983:1987 Edition
Specification for decorative laminated plastics sheet veneered boards and panels Published By Publication Date Number…
-
BS 4361-36:1990
Woodworking machines – Nomenclature for single-end tenoning machines with several spindles Published By Publication Date…
-
BS EN 20898-2:1992
Mechanical properties of fasteners – Nuts with specified proof load values Published By Publication Date…
-
BS 2782:1970:1987 Edition
Methods of testing plastics Published By Publication Date Number of Pages BSI 1987 46
-
BS EN ISO 2566-2:2001
Steel. Conversion of elongation values – Austenitic steels Published By Publication Date Number of Pages…
-
BS ISO 2966:1988:1995 Edition
Cinematography. 16 mm motion-picture film perforated 8 mm type S [1-3] and [1-4]. Cutting and…
-
BS 2569-1:1964:1968 Edition
Specification for sprayed metal coatings – Protection of iron and steel by aluminium and zinc…
-
BS 3894-2:1985
Method for converting elongation values for steel – Method of conversion for application to austenitic…
-
BS 5451:1977
Specification for electrically conducting and antistatic rubber footwear Published By Publication Date Number of Pages…
-
BS 3884-1:1974
Modular units for machine tools – Specification for basic units Published By Publication Date Number…
-
BS 2866:1984
Methods for determination of the mass of warp and weft per unit area of fabric…
-
BS 6068-6-6.2:1983
Water quality. Sampling – Guidance on sampling techniques Published By Publication Date Number of Pages…
-
BS 6829-5.1:1990
Analysis of surface active agents (raw materials). Ethoxylated alcohol and alkylphenol sulphates – Method for…
-
BS EN ISO 2556:2001
Plastics. Determination of the gas transmission rate of films and thin sheets under atmospheric pressure.…
