ISO 75-3:2004
$13.00
Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
Published By | Publication Date | Number of Pages |
ISO | 2004-05 | 12 |
If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]
ISO 75-3:2004 specifies a method for the determination of the temperature of deflection under load of high-strength thermosetting laminates and compression-moulded long-fibre-reinforced plastics in which the fibre length is greater than 7,5 mm. The flexural stress used is not fixed, as in ISO 75-2, but is a fraction (1/1000) of the initial (room-temperature) flexural modulus of the material under test. This allows the method to be applied to materials with a wide range of flexural moduli.
Published Code | ISO |
---|---|
Published By | International Organization for Standardization |
Publication Date | 2004-05 |
Pages Count | 12 |
Language | France |
Edition | 2 |
File Size | 143.4 KB |
ICS Codes | 83.080.10 - Thermosetting materials 83.120 - Reinforced plastics |
Related products
-
IEEE ISO IEC 15288 2008
Systems and software engineering System life cycle processes Published By Publication Date Number of Pages…
-
BS EN ISO 15973:2001:2004 Edition
Closed and blind rivets with break pull mandrel and protruding head. AIA/St Published By Publication…
-
BS EN ISO 7765-1:2004
Plastics film and sheeting. Determination of impact resistance by the free-falling dart method – Staircase…
-
BS EN ISO 295:2004
Plastics. Compression moulding of test specimens of thermosetting materials Published By Publication Date Number of…
-
BS EN ISO 17249:2013:2014 Edition
Safety footwear with resistance to chain saw cutting Published By Publication Date Number of Pages…
-
IEEE 1073.3.2 2000
IEEE Standard for Medical Device Communications – Transport Profile – IrDA Based – Cable Connected…
-
BS EN ISO 294-2:1998:2006 Edition
Plastics. Injection moulding of test specimens of thermoplastic materials – Small tensile bars Published By…
-
BS EN ISO 15982:2002:2004 Edition
Open end blind rivets with break pull mandrel and countersunk head. AIA/AIA Published By Publication…
-
BS EN ISO 75-1:2004
Plastics. Determination of temperature of deflection under load – General test method Published By Publication…
-
BS ISO 16609:2004:2006 Edition
Banking. Requirements for message authentication using symmetric techniques Published By Publication Date Number of Pages…
-
BS EN ISO 8295:2004
Plastics. Film and sheeting. Determination of the coefficients of friction Published By Publication Date Number…
-
BS EN IEC 60335-2-75:2023+A11:2023
Household and similar electrical appliances. Safety – Particular requirements for commercial dispensing appliances and vending…
-
BS EN ISO 22867:2008 2009
Forestry machinery. Vibration test code for portable hand-held machines with internal combustion engine. Vibration at…
-
IEEE 15288-2008
ISO/IEC/IEEE International Standard – Systems and software engineering System life cycle processes Published By Publication…
-
BS 7349-1:1993
Blind rivets with break mandrel – Specification for closed end blind rivets Published By Publication…
-
BS ISO 17288-2:2004
Passenger cars. Free-steer behaviour – Steering-pulse open-loop test method Published By Publication Date Number of…
-
IEEE 1073.3.2-2000
IEEE Standard for Medical Device Communications – Transport Profile – IrDA Based – Cable Connected…
-
BS ISO 17058:2004
Steel and iron. Determination of arsenic content. Spectrophotometric method Published By Publication Date Number of…
-
BS EN ISO 6383-2:2004
Plastics. Film and sheeting. Determination of tear resistance – Elmendorf method Published By Publication Date…
-
BS EN ISO 75-3:2004 2006
Plastics. Determination of temperature of deflection under load – High-strength thermosetting laminates and long-fibre-reinforced plastics…
-
BS EN ISO 14122-4:2004+A1:2010
Safety of machinery. Permanent means of access to machinery – Fixed ladders Published By Publication…
-
BS EN ISO 17249:2013:2014 Edition
Safety footwear with resistance to chain saw cutting Published By Publication Date Number of Pages…
-
BS EN ISO 75-2:2013
Plastics. Determination of temperature of deflection under load – Plastics and ebonite Published By Publication…
-
BS EN ISO 293:2005 2006
Plastics. Compression moulding of test specimens of thermoplastic materials Published By Publication Date Number of…
-
BS ISO 14617-11:2002:2004 Edition
Graphical symbols for diagrams – Devices for heat transfer and heat engines Published By Publication…
-
BS EN ISO 6383-1:2004
Plastics. Film and sheeting. Determination of tear resistance – Trouser tear method Published By Publication…
-
BS EN ISO 9562:2004
Water quality. Determination of adsorbable organically bound halogens (AOX) Published By Publication Date Number of…
-
BS ISO 13887:2004
Cold-reduced steel sheet of higher yield strength with improved formability Published By Publication Date Number…
-
BS EN ISO 11501:2004
Plastics. Film and sheeting. Determination of dimensional change on heating – Determination of dimensional change…
-
BS EN ISO 527-3:1996:2004 Edition
Plastics. Determination of tensile properties – Test conditions for films and sheets Published By Publication…
-
BS EN ISO 75-1:1996:1994 Edition
Plastics. Determination of temperature of deflection under load – General test method Published By Publication…
-
BS EN ISO 11064-4:2004
Ergonomic design of control centres – Layout and dimensions of workstations Published By Publication Date…
-
BS ISO 12488-4:2004
Cranes. Tolerances for wheels and travel and traversing tracks – Jib cranes Published By Publication…
-
BS EN ISO 7823-3:2004
Plastics. Poly(methyl methacrylate) sheets. Types, dimensions and characteristics – Continuous cast sheets Published By Publication…
-
BS EN ISO 75-1:2013
Plastics. Determination of temperature of deflection under load – General test method Published By Publication…
-
BS EN ISO 17249:2013:2014 Edition
Safety footwear with resistance to chain saw cutting Published By Publication Date Number of Pages…
-
BS EN ISO 14616:2004:1997 Edition
Plastics. Heatshrinkable films of polyethylene, ethylene copolymers and their mixtures. Determination of the shrinkage stress…
-
BS EN ISO 10618:2004
Carbon fibre. Determination of tensile properties of resin-impregnated yarn Published By Publication Date Number of…
-
BS EN 60730-1:2011:2012 Edition
Automatic electrical controls for household and similar use – General requirements Published By Publication Date…
-
BS EN ISO 75-2:2004 2006
Plastics. Determination of temperature of deflection under load – Plastics and ebonite Published By Publication…