{"id":126807,"date":"2024-10-19T05:41:00","date_gmt":"2024-10-19T05:41:00","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-62386-3032017a12024\/"},"modified":"2024-10-24T23:22:20","modified_gmt":"2024-10-24T23:22:20","slug":"bs-en-62386-3032017a12024","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-62386-3032017a12024\/","title":{"rendered":"BS EN 62386-303:2017+A1:2024"},"content":{"rendered":"
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
2<\/td>\n | undefined <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | CONTENTS <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | INTRODUCTION Figures Figure 1 \u2013 IEC 62386 graphical overview <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 1 Scope 2 Normative references 3 Terms and definitions <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 4 General 4.1 General 4.2 Version number 4.3 Insulation 5 Electrical specification 6 Interface power supply 7 Transmission protocol structure 8 Timing 9 Method of operation 9.1 General <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | 9.2 Instance type 9.3 Input signal and value 9.3.1 General 9.3.2 Input signal mapping for movement sensors Tables Table 1 \u2013 Meaning of \u201cinputValue\u201d <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | Figure 2 \u2013 State diagram for movement based sensor <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | 9.3.3 Input signal mapping for presence sensors Figure 3 \u2013 State diagram for presence sensor <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | 9.4 Events 9.4.1 Priority use 9.4.2 Bus usage 9.4.3 Encoding Table 11 \u2013 Presence sensor state transitions <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | 9.4.4 Event configuration Table 2 \u2013 Occupancy and vacancy events <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | 9.4.5 Event generation 9.4.6 Movement trigger and catching Table 3 \u2013 Event filter <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | 9.5 Configuring the input device 9.5.1 Using the hold timer 9.5.2 Using the report timer 9.5.3 Using the deadtime timer 9.5.4 Setting the timers <\/td>\n<\/tr>\n | ||||||
22<\/td>\n | 9.5.5 Manual configuration Table 4 \u2013 Event timer setting <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | 9.5.6 Occupancy sensor capabilities 9.5.7 Configuring the sensitivity and range Table 5 \u2013 \u201cmanualCapabilityInstance3xx\u201d values Table 12 \u2013 “occupancyCapabilities” values <\/td>\n<\/tr>\n | ||||||
24<\/td>\n | 9.6 Exception handling 9.6.1 Physical sensor failure 9.6.2 Manufacturer specific errors 9.6.3 Error value 10 Declaration of variables Table 6 \u2013 \u201cinstanceErrorByte\u201d values Table 7 \u2013 Declaration of device variables <\/td>\n<\/tr>\n | ||||||
25<\/td>\n | 11 Definition of commands 11.1 General 11.2 Overview sheets 11.2.1 General Table 8 \u2013 Restrictions to instance variables defined in IEC 62386-103:2022 Table 9 \u2013 Declaration of instance variables <\/td>\n<\/tr>\n | ||||||
26<\/td>\n | 11.2.2 Standard commands 11.3 Event messages 11.3.1 INPUT NOTIFICATION (device\/instance, event) 11.3.2 POWER NOTIFICATION (device) 11.4 Device control instructions 11.5 Device configuration instructions 11.6 Device queries Table 10 \u2013 Standard commands <\/td>\n<\/tr>\n | ||||||
27<\/td>\n | 11.7 Instance control instructions 11.7.1 General 11.7.2 CATCH MOVEMENT 11.7.3 CANCEL HOLD TIMER 11.8 Instance configuration instructions 11.8.1 General 11.8.2 SET EVENT FILTER (DTR0) 11.8.3 SET HOLD TIMER (DTR0) 11.8.4 SET REPORT TIMER (DTR0) 11.8.5 SET DEADTIME TIMER (DTR0) <\/td>\n<\/tr>\n | ||||||
28<\/td>\n | 11.8.6 SET DETECTION RANGE (DTR0) 11.8.7 SET SENSITIVITY (DTR0) 11.9 Instance queries 11.9.1 General 11.9.2 QUERY INSTANCE ERROR 11.9.3 QUERY DEADTIME TIMER 11.9.4 QUERY HOLD TIMER 11.9.5 QUERY REPORT TIMER 11.9.6 QUERY CATCHING <\/td>\n<\/tr>\n | ||||||
29<\/td>\n | 11.9.7 QUERY INSTANCE CAPABILITIES 11.9.8 QUERY DETECTION RANGE 11.9.9 QUERY SENSITIVITY 11.10 Special commands <\/td>\n<\/tr>\n | ||||||
30<\/td>\n | Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Digital addressable lighting interface – Particular requirements. Input devices. Occupancy sensor<\/b><\/p>\n |