{"id":75529,"date":"2024-10-17T17:10:04","date_gmt":"2024-10-17T17:10:04","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/astm-a999-2012\/"},"modified":"2024-10-24T19:21:51","modified_gmt":"2024-10-24T19:21:51","slug":"astm-a999-2012","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/astm\/astm-a999-2012\/","title":{"rendered":"ASTM-A999 2012"},"content":{"rendered":"<\/p>\n<p id=\"s00002\">1.1 This specification covers a group of general requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.<\/p>\n<p id=\"s00003\">1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail.<\/p>\n<p id=\"s00004\">1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units apply unless the M designation (SI) of the product specification is specified in the order.<\/p>\n<p class=\"desc\" id=\"N00002\"><span class=\"smallcap\">Note<\/span> 1The dimensionless designator NPS (nominal pipe size) is used in this standard for such traditional terms as nominal diameter, size, nominal bore, and nominal size.<\/p>\n<p id=\"s00005\">1.4 <span class=\"italic\"><span class=\"med\">The following precautionary statement pertains only to the test method portion, Section 22, of this specification:<\/span> <span class=\"italic\">This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.<\/span><\/span><\/p>\n<p><h4>PDF Catalog<\/h4>\n<table border=\"1px\" class=\"des-table\">\n<tr>\n<th>PDF Pages<\/th>\n<th>PDF Title<\/th>\n<\/tr>\n<tr>\n<td><b>1<b><\/td>\n<td>Scope <br \/> Referenced Documents  <\/td>\n<\/tr>\n<tr>\n<td><b>2<b><\/td>\n<td>Materials and Manufacture <br \/> Terminology <br \/> Ordering Information  <\/td>\n<\/tr>\n<tr>\n<td><b>3<b><\/td>\n<td>Chemical Composition <br \/> Mechanical Properties <br \/> Tensile Requirements <br \/> Permissible Variation in Mass for Seamless Pipe <br \/> Permissible Variations in Wall Thickness <br \/> Permissible Variations in Inside Diameter <br \/> Permissible Variation in Outside Diameter  <\/td>\n<\/tr>\n<tr>\n<td><b>4<b><\/td>\n<td>Permissible Variations in Length <br \/> Mass per Unit Length <br \/> Ends <br \/> Straightness <br \/> Repair by Welding <br \/> Retests <br \/> Retreatment <br \/> TABLE 1  <\/td>\n<\/tr>\n<tr>\n<td><b>5<b><\/td>\n<td>Test Specimens <br \/> Flattening Test Requirements <br \/> Nondestructive Test Requirements  <\/td>\n<\/tr>\n<tr>\n<td><b>7<b><\/td>\n<td>Inspection <br \/> Rejection <br \/> Certification  <\/td>\n<\/tr>\n<tr>\n<td><b>8<b><\/td>\n<td>Product Marking <br \/> Packaging, Marking, and Loading <br \/> Government Procurement  <\/td>\n<\/tr>\n<tr>\n<td><b>9<b><\/td>\n<td>Keywords <br \/> A1. REQUIREMENTS FOR THE INTRODUCTION OF NEW MATERIALS <br \/> A1.1  <br \/> TABLE 2  <\/td>\n<\/tr>\n<tr>\n<td><b>10<b><\/td>\n<td>X1. MINIMUM WALL THICKNESS ON INSPECTION FOR NOMINAL (AVERAGE) PIPE WALL THICKNESS <br \/> TABLE X1.1  <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"<p><b>A999\/A999M-12 Standard Specification for General Requirements for Alloy and Stainless Steel Pipe<\/b><\/p>\n<table class=\"shortdes-table\" style=\"width: 100%\" border=\"0\" cellspacing=\"0\" cellpadding=\"0\">\n<tbody>\n<tr>\n<td>Published By<\/td>\n<td>Publication Date<\/td>\n<td>Number of Pages<\/td>\n<\/tr>\n<tr>\n<td><a href=\"https:\/\/pdfstandards.shop\/product-category\/publishers\/astm\/\"><b>ASTM<\/b><\/a><\/td>\n<td>2012<\/td>\n<td>11<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":75530,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[347,2637],"product_tag":[],"class_list":{"0":"post-75529","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-23-040-10","7":"product_cat-astm","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/75529","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/75530"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=75529"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=75529"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=75529"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}